Jump to content
SAU Community

Recommended Posts

I am selling a Trust turnflow intercooler with no leaks in good condition. It has a few marks but is in good working order.

Was fitted to a stagea previously and fitted to my R34 GTT. Previous owner made 310rwkw with it and I made 279rwkw.

This intercooler does not come with any piping.

$100

Jeff 0400648813

Located in west melbourne for pickup.

post-29432-0-94752500-1310450949_thumb.jpg

post-29432-0-14274200-1310450976_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/370725-trust-turnflow-intercooler/
Share on other sites

Its a front mount intercooler. The core itself measures 500x250x70.

Turnflow means both inlet and outlet are on the same side of the intercooler. This means you can connect it up to the factory intercooler piping. This means you do not have to cut holes anywhere which cops do not like.

Its a front mount intercooler. The core itself measures 500x250x70.

Turnflow means both inlet and outlet are on the same side of the intercooler. This means you can connect it up to the factory intercooler piping. This means you do not have to cut holes anywhere which cops do not like.

In other words, air runs vertically instead of side-to-side as in more common coolers.

Although the Trust turnflow runs via factory piping you'll still need piping to connect it up, as seen here:

http://www.skylinesa...c-turnflow-kit/

This piping is not included according to original poster in this ad, so you'll have to make something up.

I've got the same kit on my 34 and it's running well, installation instructions & pics here:

http://www.skylinesa...r-installation/

Hope this helps.

  • Like 1

Ive got ur number Jeff and I'm in Geelong so maybe il try work something out. At the moment my stagea is stock. I do want it to run heaps better. This Intercooler seems to be one I like and a good brand. Any idea on piping? Keep in touch.

Fab piping cost $$$ Got a quote recently to get custom stainless piping to fit a gktech intercooler to r32gtst was like $500 drive in drive out job. Something for you to think about. If you can find a cheap place that can do custom piping please let me know too im in melb.

http://www.gktech.com.au/front.asp?pid=11&ProductID=univ%2Dnhfm

Edited by Mimz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...