Jump to content
SAU Community

Fs: 5Zigen Header For V35 And Possibly 350Z

RR33YY
 Share

Recommended Posts

RR33YY Contributor

RR33YY

Posted
Posted (edited)

Hi guys, I've got a set of 5 zigen headers up for sale. They are practically brand new. Installed for a couple of minutes then I took it off then changed it to tomei headers.

Ill be honest to you, it will fit skyline v35 but the Right header will only have a few millimetres gap from the steering shaft. Here are a few quotes from my old thread for the solutions

"They're LHD extractors. Get an extender bar and a hammer, and beat it out of the way. It should only need a few mm. That's what the workshop did with mine (after I spoke to a mate of mine with the same issue, and he recommended it as his solution).

Follow the time-honoured tradition. :)"

"Yes i had the same problem.

It still hits when turning left when the car is cold. Only just. ( might fix it one day )

They are made for Left hand drive cars. I had mine shaved a little.

Try heating the spot up it tuches and hitting with a hammer. :thumbsup:"

I will let them go for $500, please dont hesitate to contact me on 0430 195789 or drop me a message if I dont pick up the phone.

Thanks guys

headerssk.jpg

Uploaded with ImageShack.us

Edited by RR33YY
  • 1 month later...
  • 1 month later...
  • 6 months later...
  • 1 month later...
  • 11 months later...
sonicii Veteran

sonicii

Posted
Posted

Perhaps some have been put off by this -

Installed for a couple of minutes then I took it off then changed it to tomei headers.

Was it just the fitment issue that made you change to Tomei headers?

  • 3 weeks later...
RR33YY Contributor

RR33YY

Posted
  • Author
Posted

It was just the fitment. The reason why we had to take it off straight away because we ran out of time for the dyno day. We did not have enough time to play around with the headers. As y' all know installing extractors on a V engine isnt easy and time consuming. So once the tomei installed I cbf'd trying to install the 5zigen again.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      S1 rb25/s14 starting problem

      By Dose Pipe Sutututu · Posted

      When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...