Jump to content
SAU Community

Recommended Posts

Up for sale are my 19x9.5 +40 (+28 With included 12mm spacers + wheel nuts or +35 with 5mm spacers) Axis Hiro copies.

They sit perfectly flush on a M35 Stagea.

The wheels have been on my car for the past 6 or so months. In perfect condition and never grazed.

Includes Falken tyres. Some wear (see photo).

Price: $999.00 Firm. I can post interstate at buyers expense.

PM or call Chris - 0423 176 774

Here are some photos of the wheels & Tyres:

stag.jpg

NM35-long.jpg

setup.jpg

tyre.JPG

Cheers.

Chris.

Link to comment
https://www.sau.com.au/forums/topic/371618-fs-19x95-axis-hiro/
Share on other sites

I don't suppose you'd know how these would fit on a C34 series 2 manual at all?

I ran Enkei RP03 - 19" x 8.5", +22 and they sat pretty close to flush. I probably had another few mm to the guard edge, so a 9.5", +28 probably wouldn't fit, even without a spacer.

The 9.5" wheel is an extra 13mm wider than the 8.5" from the centre to each side (total 25.4mm). Less 6mm for the offset difference and you're still 6-7mm wider to the outside than my wheels. You'd be cutting it real close!

You'd also have to take into account any rubbing of the tyre on your suspension as the wheel is 13mm wider from the centre to the inside as well.

They'd look good though, especially with wide rubber; it would give a great stance from the rear.

I ran Enkei RP03 - 19" x 8.5", +22 and they sat pretty close to flush. I probably had another few mm to the guard edge, so a 9.5", +28 probably wouldn't fit, even without a spacer. The 9.5" wheel is an extra 13mm wider than the 8.5" from the centre to each side (total 25.4mm). Less 6mm for the offset difference and you're still 6-7mm wider to the outside than my wheels. You'd be cutting it real close! You'd also have to take into account any rubbing of the tyre on your

suspension as the wheel is 13mm wider from the centre to the inside as

well. They'd look good though, especially with wide rubber; it would give a great stance from the rear.

Cheers for that. I'm still trying to get my head around what will and won't fit my car. Makes it a little harder having a manual with narrower rear track and not wanting to run spacers.

Hell yeah they'd look good but I can't be arsed with the complications.

Edited by BMX666

Bmx666, after fitting stagered offset wheels to my rs4s. I think we have same front/rear track, it's the auto that has a wider rear end then the front. I bought 18x8 +6 for the rear and +35 for the front then had to fit a 25mm spacer to the front just to fix it. And by my count. These wheels should fit depending on your height, I would do a test fit if you can. 19s would fill the c34 guards so well.

Edited by lilcrash
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...