Jump to content
SAU Community

Transporting Cars Interstate

VNS 24

By VNS 24,
in General Automotive Discussion

 Share

Recommended Posts

VNS 24 Mentor

VNS 24

Posted
Posted (edited)

Hi everyone.

As topic suggests, I am bringing over my 3 cars (Mitsubishi Mirage, Nissan Dualis and Nissan Skyline V35 350GT coupe) from WA to QLD.

I just want to know what kind of process is involved in getting them register in QLD (i.e. Where to go, how much approximate costs, how long it takes, etc.).

The main car I am worried about is my V35. I am bringing over as it is, with bodykit and wheels on it. It currently sitting at 85mm from the ground to the bodykit and wheels are 19 inch (8.5 +5 F and 9.5 +12 R) with 225/35/19 front and 245/35/19 rear. I can put back stock 17 inch wheels on to have extra 10mm-15mm height but not sure if that will help at all.

Any suggestion or experience are much appreciated.

Thank you.

Edited by VNS 24
Link to comment
https://www.sau.com.au/forums/topic/372303-transporting-cars-interstate/
Share on other sites
Marlin Grand Master

Marlin

Posted
Posted

I use Ceva to transport my race car around Oz. They're quite trustworthy and slightly more capable of handling sporty cars it seems.

When you get them to Qld, you need a mechanic to inspect and give you a "raodworthy certificate", which you then take, along with the vehicle, to Qld Transport dept (offices everywhere), pays your money, have them confirm the numbers, and issue you with plates. They then post a label.

VNS 24 Mentor

VNS 24

Posted
  • Author
Posted (edited)

I use Ceva to transport my race car around Oz. They're quite trustworthy and slightly more capable of handling sporty cars it seems.

When you get them to Qld, you need a mechanic to inspect and give you a "raodworthy certificate", which you then take, along with the vehicle, to Qld Transport dept (offices everywhere), pays your money, have them confirm the numbers, and issue you with plates. They then post a label.

Hi Ben, thanks for that.

I am using CEVA too. I did tell them about my V35 being 85mm from the ground (Preferably 100mm clearance) and they said it should be fine as they had dealt with low cars before. It might scrape abit but as long as nothing major issue, it should be fine.

You being in Brisbane, would you be able to direct me to a "reputable" mechanic for a "roadworthy certificate" near Crestmead/Waterford area? Also, you wouldn't know how much are the charges go?

I think I do have a time period of up to 3 months before having to change to QLD rego plates.

Thanks, Ben.

Edited by VNS 24
-Jimmy- Mentor

-Jimmy-

Posted
Posted (edited)

When I brought my 32 over from NSW to WA, I used a website called 'Auto-move'. They sent it via GSR (Great Southern Rail).

They provided the cheapest quote I could find with my research.

When it goes via GSR, you're allowed to put items in it, and it's also quicker.

I recently did some more research to find out how much it'd cost to get my car back over in NSW and I found a company called 'Auto Logistics' which also send it via the GSR for a considerably lower price than I paid with Automove.

I wonder if I can book it thruugh GSR directly.

Edit: Just researched, the train doesn't go up to QLD so can't really help you on that one. :/

Edited by -Jimmy-
VNS 24 Mentor

VNS 24

Posted
  • Author
Posted (edited)

When I brought my 32 over from NSW to WA, I used a website called 'Auto-move'. They sent it via GSR (Great Southern Rail).

They provided the cheapest quote I could find with my research.

When it goes via GSR, you're allowed to put items in it, and it's also quicker.

I recently did some more research to find out how much it'd cost to get my car back over in NSW and I found a company called 'Auto Logistics' which also send it via the GSR for a considerably lower price than I paid with Automove.

I wonder if I can book it thruugh GSR directly.

Edit: Just researched, the train doesn't go up to QLD so can't really help you on that one. :/

Hi James, thanks for your information.

I went with CEVA because I am relocating for work and work paid for my other 2 cars (Mirage and Dualis). So I thought I would still use CEVA for my V35.

The fact that "Auto-move" company allows you to put items in the car sounds very good. I could have put my V35 stock wheels in my Dualis to save some transporting fees but couldn't do so. Oh well, sounds like they don't transport to QLD anyway, so doesn't really matter.

Thanks again, Jame. Much appreciated.

Edited by VNS 24
fastjetjockey Collaborator

fastjetjockey

Posted
Posted

You, two mates, 3x 2-way radios, 3x car bras and a decent camera. What an adventure!!

I drove my ex-girlfriend back home to Broome at the end of last year from Brisbane; It was a pretty amazing drive! Took 5 easy days,on some pretty questionable roads, in an '07 Mazda 3. If you've got the time to spare, I would recommend seeing the guts of your country.

The other option was to put the car on a train, I think it worked out to around ~$800. I think if you can find a way, the train is going to be the cheapest option. Even if you get it to Sydney then drive it north.

VNS 24 Mentor

VNS 24

Posted
  • Author
Posted (edited)

You, two mates, 3x 2-way radios, 3x car bras and a decent camera. What an adventure!!

I drove my ex-girlfriend back home to Broome at the end of last year from Brisbane; It was a pretty amazing drive! Took 5 easy days,on some pretty questionable roads, in an '07 Mazda 3. If you've got the time to spare, I would recommend seeing the guts of your country.

The other option was to put the car on a train, I think it worked out to around ~$800. I think if you can find a way, the train is going to be the cheapest option. Even if you get it to Sydney then drive it north.

Hey Dion, I do want to see the guts of the country on a road trip but I don't have the guts/time to drive the cars across the country! :P

By the way, Broome is nice. I haven't been there but seen lots of photos and plan to go there one day. :)

Edited by VNS 24
VNS 24 Mentor

VNS 24

Posted
  • Author
Posted

Hi mate currently residing in crestmead area also, Have used CEVA to transport my 33 4 door from Darwin. Had no problems car was preaty low also.

Hi mate. Nice to know you. If I see your R33 on the road, I will wave! :-)

My V35 is on the way to Brisbane now. They used tilt truck and wooden plates for more assist and it was all good.

VNS 24 Mentor

VNS 24

Posted
  • Author
Posted

I live on the other side of town but there will be a lot of roadworthy guys to chose from, even mobile ones.

Usually 80 to 100 bucks mate.

Best of luck with it all. Pm me if you need any advice ok :)

Thanks, Ben.

Would you know any mobile service provider for road worthy certificate?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...