Jump to content
SAU Community

Recommended Posts

hey guys, i have a r33 gtst skyline and have just reciently intstalled the apexi PowerFC and hand controller. The rest of the car is pretty stock, except for 3in exaust. The FC is still in its base tune. What i have noticed though is if i give it a bit, it's not too hard to get the FC to flash up 100% duty cycle for the injectors (or close to it).

whats the most logical cause for this, injectors or fuel pump on the way out?

leigh.

Link to comment
https://www.sau.com.au/forums/topic/37231-100-injector-duty/
Share on other sites

Most logical cause is the the base map is set up for greater fuel delivery to take into account more mods than you have (ie is tuned rich).

Get it on a dyno and tune according to the air/fuel ratio. Will probably find that you'll gain power as well as reduce fuel consumption.

Link to comment
https://www.sau.com.au/forums/topic/37231-100-injector-duty/#findComment-745695
Share on other sites

Guest INASNT
just get GT-R injectors ,pump,FMIC,POD and youll fly .. 13 seconds garunteed.

that wouldnt cost you much.. how much boost are you running ? you must be on atleast 11psi to max out the injectors and fpump

bahahaha!!!

U have obiliously have not done any of these in your car have ya?

B33st

If u got stock everything else then ur injectors shouldnt be maxing out.

Get the injectors ultrasonically cleaned and checked coz they must be a blockage somewhere, or your fuel pump is cactus. Also if u continue to drive your engine will be pining up high with the base maps

Link to comment
https://www.sau.com.au/forums/topic/37231-100-injector-duty/#findComment-750702
Share on other sites

I have already purchased new 044 fuel pump, sx reg, surgetank. Also no the way are a Greddy Plenum, Q45 afm + throttle body.

Had just put the FC in and given it a bit or a run to see how it would go. Ran like normal, except for the fact that the hand controler was easy to get to show 100% duty, never showed more than 17 on the knock meter though.

as soon as i get the plenum etc, will installing all the bits and taking it to ARE (QLD) for custom cooler / piping job.

then its time for a tune, and i guess i will find out if new injectors are needed too.

leigh.

Link to comment
https://www.sau.com.au/forums/topic/37231-100-injector-duty/#findComment-751564
Share on other sites

yeah am working towards the turbo...

I wanted to do my build-up in 2 stages.

1. support systems

2. big turbo and big boost.

i pretty much have all the support items now(see last post). so ill get them installed + tuned and it'll then just be a matter of waiting till i have the funds for the turbo.

leigh.

Link to comment
https://www.sau.com.au/forums/topic/37231-100-injector-duty/#findComment-753226
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...