Jump to content
SAU Community

Nistune Ecu For Ecr33

Checkbuzz
 Share

Recommended Posts

Checkbuzz Rising Star

Checkbuzz

Posted
Posted (edited)

As the title says I have a Z32 Nistune ECU for sale.

This ECU has had the Nistune type 3 daughter board fitted and has also been modded for use in the ECR33 by Nistune in SA.

This is a complete, plug-in, real-time tunable ECU solution for the ECR33 that requires no other mods or wiring.

Comes with PLMS USB consult cable worth $95!

$450 + shipping anywhere in Aus/NZ

:thanks:

Edited by Checkbuzz
Link to comment
https://www.sau.com.au/forums/topic/374113-nistune-ecu-for-ecr33/
Share on other sites
Checkbuzz Rising Star

Checkbuzz

Posted
  • Author
Posted

See below for pix (including consult cable, serial no, daughter board and wiring mods to suit R33) & yes this ECU will be good to go for the series 2 ECR33!

PM on it's way!

So its for the later model z32 board?

Im sure this would be compatable with the series 2 r33 if so

pm me your bank details and consider this sold

Thanks Christian

post-52301-0-85817900-1313403310_thumb.jpg

post-52301-0-92641600-1313404449_thumb.jpg

post-52301-0-53699600-1313404461_thumb.jpg

post-52301-0-24805800-1313404557_thumb.jpg

Checkbuzz Rising Star

Checkbuzz

Posted
  • Author
Posted (edited)

Yes you are correct mate... my mistake - as you can see from the pix it is actually a type 2 board :P

I was under the impression a r33 using z32 ecu needed a type 2 board???

Edited by Checkbuzz
sneki81 Community Regular

sneki81

Posted
Posted

Still available... lots of interest but no sale yet

If you had this for sale a week ago it would have gone the day i saw it.

I only just bought and intalled one in my 33.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • GTSBoy
      Cas issue

      By GTSBoy · Posted

      The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Duncan
      RB26DETT Sketchy boost mod?

      By Duncan · Posted

      Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...