Jump to content
SAU Community

Recommended Posts

Soon i will be commencing all sorts of repair work to my newly purchased R33 GTR, i own my own workshop & can't wait to start improving the car!!!

I will be puting up pics, info & other interesting things as i go along.

First on the agenda is the Wheels & Brakes so hope you like what i have to show & cheers for having me on your forum :cheers:

Pics will begin soon

Link to comment
https://www.sau.com.au/forums/topic/374149-my-first-gtr-r33-project/
Share on other sites

Sounds good.

As this opening post has no hard info, pics, details etc i'm putting it in the general discussion area. Once you've started and have some actual content, feel free to start in the projects section again :)

I think i have worked out why pics aren't uploading, because they are over 2mb

i took them with my i4 so clues on how to get them up???

once i get used to operating this forum i will be right but for now.....help!!:rofl2:

I think i have worked out why pics aren't uploading, because they are over 2mb

i took them with my i4 so clues on how to get them up???

once i get used to operating this forum i will be right but for now.....help!!:rofl2:

www.filedump.net all your problems are over

upload as many as you like and insert them into a post using the photo button inbetween link and email buttons :)

Given that a try, but there must be something that i'm doing wrong, sorry bout this but i've hit a wall now,

not too sure how im going to work this out unfortunately i don't know anybody to ask that also uses forums....be a lot easier if it had nuts & bolts!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...