Jump to content
SAU Community

Recommended Posts

Selling my track car as need cash for renovations

1990 track only gtr big hks single turbo setup

Hks manifold

Hks waste gate

Big hks/garrett turbo

Large fuel rail

1000cc injectors

Power fc dejetro

Hasnt been tuned for injectors yet

Serge tank and external pump

Stripped interior

Trust intercooler and piping

Fibaglass front bar

Fibaglass front gaurds

Fibaglass boot with n1 lip

Brand new comp stage 5 clutch

Needs finishing but will be a fast car

Internals unknown asume stock

Heaps of spares

Contact 0411672105

Located central coast nsw

$12500

SWAP FOR CHEAPER TRACK CAR AND CASH

Link to comment
https://www.sau.com.au/forums/topic/374941-r32-gtr-hks-single-turbo-setup/
Share on other sites

  • 2 weeks later...
  • 1 month later...

Track only inport...

New yellowjack coil packs and spark plugs starts and runs but rich as. touch up tune and will make 320-350 wkws

Make some offers trade ins welcome

  • 2 weeks later...

Is this over priced or do I just need to wait for some interest

im not expert but maybe for a non register-able track only gtr.. im looking for a track only gtr but not willing to spend that much. i have seen a few on here (already sold) for around the 7k mark which might be more like it.

http://www.skylinesaustralia.com/forums/topic/358302-r32-gtr-track-car-7000/

im not expert but maybe for a non register-able track only gtr.. im looking for a track only gtr but not willing to spend that much. i have seen a few on here (already sold) for around the 7k mark which might be more like it.

http://www.skylinesaustralia.com/forums/topic/358302-r32-gtr-track-car-7000/

That's a good price for a base unit has 1500 in ecu and over 2k on the hot side let alone and also fuel system over 1k clutch band new over 600 that's y I think its worth 10k. It owes more and only had for 6 months and never even drove It

i remember this on ebay from the fiberglass front and the turbo setup, it had 2 sets of wheels on it and said it needed a tune in the post, i remember the price it was listed at but there is no point writing that up, when you picked it up was it running rough?

if so what was the problem?

what things have you done to it since purchase?

and what sort of compression does the motor have?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...