Jump to content
SAU Community

Recommended Posts

Selling my track car as need cash for renovations

1990 track only gtr big hks single turbo setup

Hks manifold

Hks waste gate

Big hks/garrett turbo

Large fuel rail

1000cc injectors

Power fc dejetro

Hasnt been tuned for injectors yet

Serge tank and external pump

Stripped interior

Trust intercooler and piping

Fibaglass front bar

Fibaglass front gaurds

Fibaglass boot with n1 lip

Brand new comp stage 5 clutch

Needs finishing but will be a fast car

Internals unknown asume stock

Heaps of spares

Contact 0411672105

Located central coast nsw

$12500

SWAP FOR CHEAPER TRACK CAR AND CASH

Link to comment
https://www.sau.com.au/forums/topic/374941-r32-gtr-hks-single-turbo-setup/
Share on other sites

  • 2 weeks later...
  • 1 month later...

Track only inport...

New yellowjack coil packs and spark plugs starts and runs but rich as. touch up tune and will make 320-350 wkws

Make some offers trade ins welcome

  • 2 weeks later...

Is this over priced or do I just need to wait for some interest

im not expert but maybe for a non register-able track only gtr.. im looking for a track only gtr but not willing to spend that much. i have seen a few on here (already sold) for around the 7k mark which might be more like it.

http://www.skylinesaustralia.com/forums/topic/358302-r32-gtr-track-car-7000/

im not expert but maybe for a non register-able track only gtr.. im looking for a track only gtr but not willing to spend that much. i have seen a few on here (already sold) for around the 7k mark which might be more like it.

http://www.skylinesaustralia.com/forums/topic/358302-r32-gtr-track-car-7000/

That's a good price for a base unit has 1500 in ecu and over 2k on the hot side let alone and also fuel system over 1k clutch band new over 600 that's y I think its worth 10k. It owes more and only had for 6 months and never even drove It

i remember this on ebay from the fiberglass front and the turbo setup, it had 2 sets of wheels on it and said it needed a tune in the post, i remember the price it was listed at but there is no point writing that up, when you picked it up was it running rough?

if so what was the problem?

what things have you done to it since purchase?

and what sort of compression does the motor have?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...