Jump to content
SAU Community

Series 1 Rb20Det Engine, Wiring Loom, And Accesories

filo_a31
 Share

Recommended Posts

filo_a31 Collaborator

filo_a31

Posted
Posted

For sale is the motor out of my ceffy that i wrote off. Motor has 15X,XXXkm's on it. Timing belt was replaced at 100,000. Runs smoothly. Was compression tested about a month before it was written off and showed good comp on all 6 cylinders. Parts not included are turbo, computer, injectors crossover pipe, engine mounts. More suitable as a replacement motor due to these parts missing. asking $700. Will part out accessories seperately if requested, eg starter, alternator, a/c compressor, afm, p/steer pump. series 2 rb20 tps sensor and plug is used in wiring harness. No oil leaks, rear main seal, rocker cover gaskets and spark plugs done recently.

filo_a31 Collaborator

filo_a31

Posted
  • Author
Posted

Part out coilpacks, coilpack loom and ignitor? Is it silvertop eccs with redtop style ignitor, coils n afm?

Yes it is. PM sent

  • 2 weeks later...
  • 3 weeks later...
  • 2 months later...
WrenchesInTheGears Enthusiast

WrenchesInTheGears

Posted
Posted

gday mate

do u know if the flywheel/clutch and exhaust manifold will fit a redtop rb20?

If so i may be keen on these items shipped to 5085

let me know some prices :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...