Jump to content
SAU Community

Recommended Posts

Hey Guys,

Up for sale is my genuine Nissan Aero front bar which was bought brand new and is less than 2000KM old.

It was repainted pewter silver and is in mint condition with little to no scratches on the bar.

These front bars are $3000 from Nissan. This bar comes with fog lights.

Price: $1500 ono

post-86687-0-39790400-1316680156_thumb.jpg

post-86687-0-11351400-1316680188_thumb.jpg

post-86687-0-06666600-1316680206.txt

post-86687-0-65061200-1316680242_thumb.jpg

I am also selling my Genuine Rays Nismo LM GT3 17inch forged 2 piece rims:) These some with the full set of 4:)

These are in good condition and with only one of the rims having gutter rash on them.

Fronts rims are 5 x 114.3 and are 17"x8.0 with offset of +36

Rear rims are 5 x 114.3 and are 17"x9.0 with offset of +38

All four rims have Kuhmo KU36's tyres on them. These tyres are awesome street tyres and are very stick when heated up.

The tyres on the fronts are 235/45/r17 with 95% tyre thread left.

The rears are 255/40/r17 with about 95% thread left.

The listed price is $1200 however the price is negotiable.

post-86687-0-47861300-1316680265_thumb.jpg

post-86687-0-30932200-1316680278_thumb.jpg

post-86687-0-00574900-1316680304_thumb.jpg

post-86687-0-58455700-1316680320_thumb.jpg

post-86687-0-39790400-1316680156_thumb.jpg

post-86687-0-02252700-1316680339_thumb.jpg

Edited by s15kid

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...