Jump to content
SAU Community

Recommended Posts

Hi,

Tried this in the maintenance forum but got no responses, so here go. I have a few questions regarding headlights on the R32, specifically the GT-R:

* Are the headlights the same across the R32 range?

* I understand there are two different types of R32 headlights: one fitted to earlier cars, one to later cars. Is this correct?

* Does anyone have measurements for the lights?

* Can anyone provide close up pictures of the two types?

* Better yet, does anyone have pictures of the headlights with the glass front removed?

Thanks,

Lucien.

Link to comment
https://www.sau.com.au/forums/topic/37813-r32-headlight-questions/
Share on other sites

  • Replies 99
  • Created
  • Last Reply

Top Posters In This Topic

i think only the 89 model had different lights cos the front indicaters were clear not orange. so that is maybe why they changed the actually head light cos of the different design or something.. thats about all i got.

GTR headlights changed slightly in wattage in 1991, other than that it should be the same for the GTR. THe GTSt's changed all over the place, but not the GTR.

Wattage doesn't really bother me, I am more interested in changes to the reflectors, projectors, etc, etc (ie. the construction of the headlight) :D

LW.

you're thinking N1 headlights anfd GTR headlights... I guess they're both GTR's but N1 headlights are a lot more expensive and rarer. Two Square = N1, Square + Round = GTR.

There's a lot of Square + Rounded Square goin around which are 1989 pov pack headlights off Type G's. A lot of people think these are N1 but they're not.

the only difference between the GTR ones and the rest of em is the clip for the nosepiece that goes inbetween the bonnet and the bumper. So if you tried to fit GTS/t ones you could on a GTR (the brackets to mount it are all the same) but you won't be able to put your nose thingy on.

r32_headlight_n1.jpg

Not really 2 square ones, but it has a higher intensity inner bulb and was only available on race equipped GTR's (which had the N1 spec RB26DETT). Also back light takes up the entire headlight, and the inner light sits on top of it.

r32_headlight_no_ring.jpg

R32 headlights with no ring on the "projector"

r32_headlight_with_ring.jpg

R32 headlights with the ring on the projector

r32_headlight_pov_pack.jpg

Very similar to the N1, cept that it used low power bulbs and the back light takes up half the headlight only.

r32_headlight_aftermarket1.jpg

r32_headlight_aftermarket2.jpg

And these are a set of aftermarket headlights that I'm getting :rofl:

god knows, they seem to pop up on a couple of drift spec r32's, still trying to find out who manufactures them... they're basically the same globes but mounted on the outside withouta glass cover... the one above the last one is the same headlight close up...

that explains why my headlights are slightly different... left has the ring & right is like the one with 208 next to it.

despite the slight differences in design they both have the same intesity & beam spread on my car.

the only difference between the GTR ones and the rest of em is the clip for the nosepiece that goes inbetween the bonnet and the bumper. So if you tried to fit GTS/t ones you could on a GTR (the brackets to mount it are all the same) but you won't be able to put your nose thingy on.

Do you have pictures of the clip in question... ?

LW.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...