Jump to content
SAU Community

Recommended Posts

2x HKS 25/40 Turbo's off an RB26 complete with 1 bar actuators. The plate on the turbo says GT2540-46T and below that is 446179-17. One is in perfect condition and the other needs to be rebuilt with new bearings and seals. WILL NOT Seperate, only selling as a pair... PRICE FOR BOTH: $1150 ono

Chipped & Tuned ECU for a R33 GTR Skyline by Electrical Magic Charge in Japan... it has been used previously! Not by me, i bought it off a friend who had it laying around... PRICE: $150 ono post-64667-1754461_thumb.jpg

HKS F-Con V ECU (Fuel & Ignition Timing) for a R32 GTR Nissan Skyline complete with patch harness... it has been used previously, i havent used it myself, i got it off of a friend! PRICE: $250ono

Apexi Rev/Speed Meter which includes 0-100-400 time/switch control... PRICE: $180ono

Call me if your interested... i only know as much about these items as what i have listed so far!! Located in Sydney, near Hurstville Joel 0421 503 250

Edited by LU57IN
Link to comment
https://www.sau.com.au/forums/topic/379658-parts-for-sale-garage-clean-out/
Share on other sites

For anyone intending to buy the HKS F-Con V-Pro (if it is the Pro) ECU in Sydney, the recommended places that'll help you tune your car with it are...

* Tune House at Marrickville

* Dart Automotive at Punchbowl

Hope this helps...

Thanx for that Terry :)

The rev speed meter has a Black Face, the serial number sticker has a mounting plate over it but the only numbers i can see are: RSM 9606!! Cheers

Yes i've been told by a mechanic they are okay for a standard RB26 and they bolt up to standard manifold/dumps... just so your aware, one needs to be rebuilt! i can post, it'll be around $70 if your in ACT!

Turbo's are SOLD!!!

Payment pending on the HKS F-Con V ECU!!!

I also have Apexi (FC Commander) Hand Controllers FOR SALE @ $250ono....They have been used previously, but are still in good, working condition!!

33 GTR ECU is SOLD!!!

STill For SALE:

1. Apexi RevSpeedMeter = $170ono

2. Apexi FC Commander (Hand Controller) = $250ono

3. R34 GTR V-Spec 2 Nur- standard ECU including the facotry boost solenoid = $300ono

4. Apexi Power FC (ECU) & Apexi Hand Controller to suit a R34 GTR = $960ono

  • 4 weeks later...

STill For SALE:

1. Apexi RevSpeedMeter = $1490ono

2. Apexi FC Commander (Hand Controller) = $249ono

3. R34 GTR V-Spec 2 Nur- standard ECU including the facotry boost solenoid = $300ono

4. Apexi Power FC (ECU) & Apexi Hand Controller to suit a R34 GTR = $960ono

Apexi RSM (Rev Speed Meter) is SOLD!!!

1. Apexi Power FC (ECU) & Apexi Hand Controller to suit a R34 GTR = $960ono:

post-64667-0-06256100-1324455157_thumb.jpg

2. Apexi FC Commander (Hand Controller) = $249ono:

post-64667-0-99707700-1324455253_thumb.jpg

3. R34 GTR V-Spec 2 Nur- standard ECU including the facotry boost solenoid = $300ono

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...