Jump to content
SAU Community

Rb30 Twin Cam Top Dead Center For Crank Shaft

BMYHOE

By BMYHOE,
in Engines & Forced Induction

 Share

Recommended Posts

BMYHOE Proficient

BMYHOE

Posted
Posted

Hey Guys,

So i just brought a R33 GTST with a RB2530 in it, the wedge holding the harmonic balancer has come loose and stuffed the crank so im in the process of replacing the crank. have the other one getting balanced etc..

so before i started pulling everything down i had the motor at TDC, but after lossing the flywheel bolts i have turned the motor almost half a turn without realising.

THEN i removed the timing belt without marking it on the belt,crank or cam gears.

so now i have the belt off and the tdc markers on the cam gears facing: inlet: 4PM outlet: 8AM

just woundering if i should re install the belt?then turn the motor to TDC?

The Mafia Grand Master

The Mafia

Posted
Posted

No need mate. There are dots you line up on the crank, and cam gears. Just line all the dots up and slip the belt on.

I urge you to check it 10 times and have a smart mate look and see if the dots line up good. I had my iPhone down there taking pics of the crank dot because you can't get your head down there to look at it straight on.

Once all the dots are lined up, slip the belt on and problem solved.

You shouldnt really use marks and hop it goes on in the same place anyway, that's just being hopeful, and not good practice.

BMYHOE Proficient

BMYHOE

Posted
  • Author
Posted

If you are srtipping the motor why are you worried about TDC?

i am just changing the crank so i didnt want to pull the head apart. i guess ill take the rocket covers off and just put the cams at TDC before re instaling the crank.

so is there any marks on the crank for TDC?

do i use the key wedges for the pulleys or is there marks on the pulleys them selfs?

sorry for the noob questions just wanna make sure things are right,

thanks

DAN

r33_racer Grand Master

r33_racer

Posted
Posted

Just use a dial indicator to find exact tdc with number 1 if you have one. Or use the marking on the timing gear to line up with the notch in the oil pump housing. Then use the cam gear dots to line up with the markings on the timing cover backing plate.

Usually tdc is is when the key slot for the woodruff key is facing up.

zebra Grand Master

zebra

Posted
Posted

Or be dodgy like me and use a pen down the #1 plug hole to get it as close as possible and adjust to get everything lined up.

I dont suggest that method though...Dial gauge is much better

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

no need to take the rocker covers off, just leave the cam gears on and line the dots up to the marks on the rear timing cover. if you turn the crank roughly 60 degrees past tdc you can turn the cams without any risk of piston to valve contact

D_Stirls Veteran

D_Stirls

Posted
Posted (edited)

Whip the cams out and then spin the crank to your hearts content, that way while you are putting the engine back together you don't have to worry about any unforeseen piston on valve action.

Edited by D_Stirls
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

did your old rb30 crank have a collar fitted?

if so can you take pics of the snout of the crank of the new crank and the old one.

I might be able to pinpoint WHY this happened and save it from happening to you again a second time. Changing the crank and not investigating WHY it happened is not the right way to go about it if you don't want it to happen again.

let me know if you want my help.

BMYHOE Proficient

BMYHOE

Posted
  • Author
Posted (edited)

thanks guys!

im getting my new crank back on wednesday, then ill get you some pics guilty.

what do you think could of been the cause?

Edited by BMYHOE
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

i have an idea.. and it happened to me before....

crank bolts DONT come lose on their own.

just make sure you send me the pics before you put it back together. pm me if i dont see them straight away.

thanks guys!

im getting my new crank back on wednesday, then ill get you some pics guilty.

what do you think could of been the cause?

BMYHOE Proficient

BMYHOE

Posted
  • Author
Posted (edited)

Sorry mate been busy ...

this is the f'd crank

post-59990-0-37536900-1320148560_thumb.jpg post-59990-0-00373000-1320148636_thumb.jpg post-59990-0-28313800-1320148660_thumb.jpg

this is the new crank

post-59990-0-44339300-1320148739_thumb.jpg post-59990-0-15828100-1320148784_thumb.jpg

i didnt get any more pics of the new crank, hopefully that will help you.

we think that this was all caused by the harmonic balancer bolt coming loose..

Edited by BMYHOE

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...