Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

yer my 32 with 25 would happily rev at 7800 at 270kw with my 4kg aloy fly wheel with the same turbo set up as simon-r32

the t67 on a 20 might not be to good haha but i have been thinking about it

Ifraz (sp) makes 640hp at the wheels with his RB20. Pretty sure it has standard rods and yes RB20's will do 9k every day. Even with standard rods mine didn't fail until the oil pump finally let go. It saw 9k rpm most of the day for 18 months. Put in some rod bolts and it will survive.

If you want to rev to 10k + I would get a forged crank for a 26 and do up the Neo engine with a 2.8 stroker. 290 - 310 degree x 10.5mm lift cams and all the supertech gear in the head.

It will swallow babies but it will sound like an FA-18 on take off.

iv pulled down a few 20s and 25s its seems to be no proplem to install a 20 crank and rods in a 25 block

so a shorter stroke and a comp ratio of around 7:1, but i could get the block decked to bring pistons back to level

My only advice would be to wear protection.

If you are going to hang your dick out the window, which it sounds like that is all you want to do, don't be upset when the guy with the better setup passes you sideways

My only advice would be to wear protection.

If you are going to hang your dick out the window, which it sounds like that is all you want to do, don't be upset when the guy with the better setup passes you sideways

LOL best post this year.

The most insane RB track car I've ever heard, as well as a large amount of guys from the drifting in melbourne was powered by a stock RB25.

Of course if it had 290 degree cams and a smaller stroke crank with custom rods and pistons it would've been better

Panik hands down for me, best sounding RB I have ever heard :)

Sounds similar to the car Steve speaking about. Not sure which i prefer, hard to get the exact from video but having seen the other car in person it was certainly the winner. Best I've heard in 10 years!

Stock 25 head, 3ltr, 6boost manifold with a gtx35. Not sure of the gate/exhaust combo etc.

Sound is as much to do with the manifold, exhaust, gate size, angle/length of screamer as it is RPM anyway.

You could rev to 9000rpm and it could sound shithouse.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...