Jump to content
SAU Community

For Sale ! R34 Gt-T Shell And Bits

rb20-into-mr30=
 Share

Recommended Posts

rb20-into-mr30= Collaborator

rb20-into-mr30=

Posted
Posted

hey guys and girls, I found a r32 gtr at a price i couldnt refuse so I regrettibly have to get rid of my r34 project.

it was to be a z-tune replica with an ls1 but I cant have 2 projects on the go.

so basiclly i have the r34 gtt shell and parts as follows:

1 spare drivers door

front hubs

2 front cross members

2 spare tail lights minus plastic garnish

front and rear suspension (std)

2 dash pads

there are no front or rear reo's or bumpers nor side skirts either.

the shell has rear drive train including the auto tailshaft, and every thing is there for the front I just need a few bolts to be able to put it back together.

It has a shopping trolley under the front to keep it rolling.

As for the shell itself, it was a repairable write off with minor damage on the front drivers headlight and a nasty

cut down the drivers side, hence the spare door(same colour) I was going to put gtr rear guards on to cover it up.

I would prefer to sell the whole lot( shell and parts) in one go for $1400 but if there is no interest in that I will happily part it out

at cost price or less. i bought all the parts and spares from fellow sau users real cheap so in return i'll sell them cheap.:cheers:

Location is adelaide and I am happy to post parts with e-go or aus post.

It was to be a time attack project so I was never worried about getting it rego'd but it can be done.

However it would still be an awsome track car as there are'nt many r34's doing time attack or even drift.

best contact is 0420 734 794 or pm me here. pics will up this weekend as i have camera issuse but i'll throw some temp ones up later tonight.

cheers, troy

Link to comment
https://www.sau.com.au/forums/topic/379855-for-sale-r34-gt-t-shell-and-bits/
Share on other sites
rb20-into-mr30= Collaborator

rb20-into-mr30=

Posted
  • Author
Posted (edited)

bump!!

also found a rear reo bar

and 1 complete r/h rear tail light

the other tail lights are only good for the coloured lens :thumbsup:

price drop to $1200 with free delivery within adelaide.

Edited by rb20-into-mr30=
  • 2 weeks later...
rb20-into-mr30= Collaborator

rb20-into-mr30=

Posted
  • Author
Posted (edited)

now with s14/r33 wheels and i have started fixing the r/hand head light section for replacement

and I have assembled the front and rear suspension so all springs and shocks are fitted and car is now steering and fully rolling on 4 wheels

also now advertising on gumtree and ebay :cheers:

Edited by rb20-into-mr30=

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • f00stx
      Quieter performance exhausts (or muffler add-on options)

      By f00stx · Posted

      So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...