Jump to content
SAU Community

Recommended Posts

Hello everyone,

just a pondering question, is it possible to make 32r running 4wd all the time without using the current electronic control system. In other word I want to cancel all sensors and ecu and make it run awd permanently without headache .

Is it possible to cancel actuator from gear box and weld nut to press on clutches or keep then in engaged position all the time.

Link to comment
https://www.sau.com.au/forums/topic/380133-how-to-make-32gtr-run-awd-directly/
Share on other sites

The pump unit isn't deisgned for continuous duty, but you mentioned getting rid of all that.

The transfer case clutch pack setup, if locked permanently would either:

suffer from 'wind up', if used on tarmac, as there can be slight differences in driveline rotation front to rear, and that will break stuff.

you will have mad understeer due to the constant locked 4wd mode!!!

The only way to do it properly would be to change the transfer case to a center diff arrangement as used in the subaru's and evo lancers....

Yes you can do it, no it's not a wise move. Not only will you reduce the hp driven to the wheels to give you acceleration, but you will destroy the transfer case from binding the clutchpacks too much

This + the BSM GTR tore the front diff off the sump running 50-50 4wd

they did find they were quicker on the track though (IIRC)

Locking the transfer is no drama, BSM did it with a solid transfer. I also did a similar thing with a machined shaft.

However both cars I know ended up with front diffs sprawled all over the circuit.

The speed gains were negligible. We found the only gain was in top speeds reached on the straights as exit acceleration was slightly faster. Entry and mid corner speed was actually slightly slower.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
×
×
  • Create New...