Jump to content
SAU Community

Recommended Posts

Hi

I have an r32 4 door rb 20 det manual my son handed down to me.

It has a heap of mods but is too lagy down low compared to my xr6 turbo and v8 so I have decided to drop a v8 into it.

From what I can find out it is a reasonably easy conversion and has heaps more room to work on plus is lighter than the original engine.

Should be a quick and stealthy car when finished.

Any one here done a chev conversion.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/380585-ls2-v8-transplant/
Share on other sites

Hi

I have an r32 4 door rb 20 det manual my son handed down to me.

It has a heap of mods but is too lagy down low compared to my xr6 turbo and v8 so I have decided to drop a v8 into it.

From what I can find out it is a reasonably easy conversion and has heaps more room to work on plus is lighter than the original engine.

Should be a quick and stealthy car when finished.

Any one here done a chev conversion.

Cheers

If you don't have the ability to do the work yourself, budget a MINIMUM of 20K. If you do have the ability to do it yourself, you will need a basic budget of 10K (That's just buying stuff, and fabbing it...)

I'm halfway through putting an LS1 into my R33. It doesn't leave you with more room, in fact, you end up with less. The motor is the exact same length as an RB26 (I had both sitting side by side) and is MUCH wider. You also need to factor in getting a 2.5" exhaust pipe down past the steering column.

You will need custom mounts, custom tail shaft, to fabricate up clutch lines, all intake to be custom, radiator lines modified etc etc.

Basically EVERYTHING needs to be custom.

It is NOT a simple conversion, although you really don't have to cut much, just that everything needs to be custom made.

Engine is lighter, but the gearbox is heavier, you end up winning by around 20 to 50KG at max.

Edit: I'm also making things easier and ditching all emmisions gear as this is going to be track only.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...