Jump to content
SAU Community

RB26/30 for sale! Will handle 1000+hp

PVL-747
 Share

Recommended Posts

PVL-747 Community Regular

PVL-747

Posted
Posted (edited)

I am selling my RB26/30 motor built by Subzero Racing.

Spec's include...

Bottom end line bored, o-ringed, heat treated, lunati 4340 rods, forged pistons, chrome moly rings, ARP bolt's, crankshaft balanced and nitrided, engine deburred and blue printed, nismo water pump, RB26 head serviced, race ported, TODA cams 10.2 mm lift 282 deg duration, TODA cam gears, ARP head stud kit, custom Subzero plenum, chrome covers, custom dry sump (does not include pump just the sump itself) or wet sump.

Subzero guarentee's 1000hp. Same motor powered TRY09's to 9.46 @ 151mph.

Sell $13,000.

I'm on the Gold Coast, QLD.

Mob: 0403 185 817.

Conditions of sale: cash only, pick up only.

Cheers

Aaron.

post-192-1131252238.jpg

Edited by PVL-747
Link to comment
https://www.sau.com.au/forums/topic/38089-rb2630-for-sale-will-handle-1000hp/
Share on other sites
  • 3 months later...
  • 1 year later...
  • 7 months later...
PranK Grand Master

PranK

Posted
Posted
wasn't this engine sold about 1 month ago

Are you serious? You reply to an 8 month old thread asking that question?

date='5 Nov 2005

Thread closed...

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • nash47
      Cas issue

      By nash47 · Posted

      Yes sir am asking is there possible way from aem tuner from wiring pins 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...