Jump to content
SAU Community

Recommended Posts

Hi All,

As topic states i'm returning car to stock so all the goodies are up for sale, open to all offers but not in rush to sell.

Car currently makes 240rwkw with the mods:

HKS GT2835 turbo - rebuilt before being put on the car... has done about 10,000K's will check condition when it comes off car, comes with braided lines and everything

$1900

s15 JDM turbo injectors - Works perfect not sure of max power, i believe it to be 280rwkw, perfect size for this setup

$500 for all six

z32 AFM - Works perfect

$250

Apexi PowerFC with hand controller - tuned for above setup

$1500

SplitFire Coilpacks - Never missed - around 2 years old

$450

Blitz Duel Solenoid Boost Controller

$350

Bosche 044 fuel pump - will come with bracket, fuel hoses and fittings

$300

Apexi POD Filter - needs cleaning,

$50

Hybrid Copy Intercooler with piping - has worked perfect since instal

$150

GTR PE2 exhaust (apexi brand i think) - only 1 year old, somehow managed to fit it onto my car came off a 33GTR, (cost $1200 new)

$550

Apexi Boost gauge, blue light, black backing -

$70

Sauber Oil temp gauge with oil filter sandwich plate installation kit -

$70

A stock white r33 GTST - everything else in reasonable nick, comes with VOLK 18's (arthur exchange), needs new rears, will come registered, has done 144xxxKs

$4900

Will post pics another time

Other odds and end that are not on the car: tubosmart BOB, Blitz SQQL BOV, rear pods (bodykit), will give away free to some1 that buys wants to buy the majority of things here.

Located in Surry Hills, but u will probably have to pick up most of this stuff from the garage i end up taking the car to.

I have probably missed some stuff. Any questions let me know.

For contact plz email [email protected] - i check emails daily

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...