Jump to content
SAU Community

Recommended Posts

Hey guys, i'm looking to get a nistune done this saturday, my R34 use to be NA, at the end of 2009 i did a turbo conversion (put a neo6 turbo motor in with turbo, NOT bolted on)

and basically i am not sure if my fuel pump was changed to the turbo one as i have heard they look identical the NA and GTT fuel pump but have different fuel flow rates?

my concern is that IF i still have the NA one, i would have to change it immediately before i get the nistune done? My car has the basics, pod, return flow front mount, full exhaust and boost t running 12psi. I am guessing it has been changed but wouldn't have a clue, is there anyway to find out if my fuel pump is the NA one or turbo.

Also what are peoples thoughts on getting a nistune done with the standard fuel pump. the turbo in the car is also standard.

any answers to help me out asap would be great thanks

Link to comment
https://www.sau.com.au/forums/topic/382479-r34-gtt-fuel-pump-issuedifference/
Share on other sites

yeah fitted the walbro today. was a c*** of a thing to do.. pretty sure it was still the factory NA fuel pump due to the extreme difficulties of taking it out... definatly never been changed. ah well. all good

yeah fitted the walbro today. was a c*** of a thing to do.. pretty sure it was still the factory NA fuel pump due to the extreme difficulties of taking it out... definatly never been changed. ah well. all good

Lol no, it's a bitch of a job anyway. It gets easier the more you do it ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...