Jump to content
SAU Community

R33 Front Bar, Rear Pods, Bonnet Lip, Bov & Amp

grantdlr
 Share

Recommended Posts

grantdlr Contributor

grantdlr

Posted
Posted

Up for sale

r33 Front Bar (FibreGlass) All grilles included, genuine Nissan clear front indicators, genuine Nissane Brake cooler ducts

Bar is in great condition and has been reinforced

After $350 (Sorry No shipping

r33 Rear Pods (FirbreGlass) no crakcs or breaks, very good condition

$120 ($30 Delivery)

r33 Bonnet Lip (Plastic) no crakcs or breaks, very good condition

$50 ($15 Delivery

Blitz Blowoff Valve. perfect condition

$60 ($10 Delivery)

Polk Audio 3 Channel Amp. very good condition

$100 ($20 Delivery)

Pickup is at Bayswater North

Email me at [email protected]

or PM me.

dscf0350u.th.jpg

dscf0351n.th.jpg

dscf0352mn.th.jpg

dscf0353s.th.jpg

dscf0354k.th.jpg

dscf0355k.th.jpg

dscf0356a.th.jpg

dscf0357i.th.jpg

dscf0358e.th.jpg

dscf0359g.th.jpg

dscf0360y.th.jpg

dscf0361du.th.jpg

dscf0362oh.th.jpg

dscf0363.th.jpg

dscf0364g.th.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...