Jump to content
SAU Community

Impul Ns-01R *forged Wheels* + Yokohama Advan Ad07

almotor
 Share

Recommended Posts

almotor Rookie

almotor

Posted
Posted

For sale: Set of RARE Forged IMPUL NS-01R *around 6.5 kgs each !!*

Staggered

PCD: 5x114

Lighter than TE37s !!

Gold in colour, some of sticker is worn

2 x 17x7.5 +35 comes with 215/45/17

2 x 17x8.5 +38 comes with 235/45/17

Both tyres have about 80% tread left

Price and price conditions: $1300 ONO, just make an offer you never know

Pictures: Google for time being, will get pictures up when i have some time

For sale: Set of 4 - 245/45/17 ADVAN AD07 - perfect for track/street

Price and price conditions: CHEAP $500 ONO , retail for roughly 350ish ea - 2 x 60%, 2 x like new

Pictures:

dscn0289r.jpg

dscn0292t.jpg

  • 1 month later...
mungy Experienced

mungy

Posted
Posted (edited)

AND btw just by looking at the amount of spokes u have there, they most likely not impul NS-01R's, they should have 5 spokes only, i can see 4 just at the top of that pic

Edited by mungy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...