Jump to content
SAU Community

Recommended Posts

price of pro gate 50mm please ?

Hey,

We have them at run out price @ $660 incl. delivery.

That's for a genuine Turbosmart Pro-Gate!

- Brendan

Hey mate, can you give me a price on a FPR and a 40mm waste gate please?

With postage to 4341 qld

Hey Cody,

Good to hear from you again!

The 40mm gate I can do for $460 incl. delivery. As with all our Turbosmart products it's a 100% genuine.

What size FPR are you looking at? 800, 1200, 2000 or 3000?-

- Brendan

Hey can you give me a price check on kompact bov for r34 gtt with adapter. post 2208 nsw

Thanks

Edited by grim reaper

Hey can you give me a price check on kompact bov for r34 gtt with adapter. post 2208 new

Thanks

Hey,

Direct-fit Turbosmart Kompact BOV (plumb-back) would be $175 incl. delivery to 2208.

- Brendan

  • 2 weeks later...

hey Brendan

sorry for the late reply, I've been flat out with work.

I actually have no idea what the difference is, what would you recommend?

Its for a R32 sedan with a RB25det neo motor in it.

hey Brendan

sorry for the late reply, I've been flat out with work.

I actually have no idea what the difference is, what would you recommend?

Its for a R32 sedan with a RB25det neo motor in it.

Hey,

No probs mate.

If it's a stock standard set-up I would just go with the FPR-800, it's got the smallest size fittings (1/8NPT) and they go up from that.

I can do one $210.

- Brendan

its no where near stock man haha. how much could you do a 1200 for?

Lol my bad.

The FPR1200 is intended for 1200HP fuel system comes with -6 fittings - price $260.

  • 4 weeks later...

Hey buddy after fuel reg with guage deliver to vic how much?

Hey,

What size reg. are you looking for? 800, 1200, 2000 or 3000? They vary in size from 1/8NPT fitting to -10AN.

- Brendan

(VM)

  • 4 weeks later...

Hi how much are the dual stage boost controllers?

Hey,

Price on one of them would be $270 incl. delivery - blue or black.

Genuine Turbosmart great that is locally delivered not coming from overseas.

Let me know what you think

Brendan

(VM)

  • 2 months later...

Do the Nissan dual port BOV's have a blanking plug to block off the trumpet side? It appears they also have adjustable spring hardness by rotating the top, is that correct?




  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...