Jump to content
SAU Community

Recommended Posts

Hi guys suprisingly I am considering selling my 200sx s15. Bought the car dead stock under the bonnet with only mod being a turbo back exhaust. I am the second owner of the car. First owner was a federal police officer and bought this car brand new back in 2000. The car has been serviced by hornsby nissan dealer since new, has full logbook stamps for every single service. I am not trying to talk up my car but it is literally in showroom condition. It is red and as you all know red color fades if not taken care properly.

2000 200sx s15 spec S

59500kms

Now the car has a low mount HKS GT-RS turbo setup along with all other supporting mods which were all purchased brand new. Here is a list of all mods :

- HKS GT-RS turbo

- Trust spec LS front mount intercooler

- Tomei fuel pump

- Nismo 740cc injectors

- SMB turbo back exhaust system

- Bosch Z32 AFM

- Apexi super suction kit

- Apexi Power FC with updated hand controller

- Apexi AVC-R boost controller

As you can see, I retained factory cams, ignition coil and exhaust manifold. Car was dyno tuned to 235rwkw @ 18psi with AFR of 11.8 : 1(high boost) and 190rwkw @ 14psi with AFR of 12.2 : 1. All work and tuning was carried out at boostech in five dock.

Here is a photo of the car when stock and engine bay with mods

299122_10150447231837329_562992328_10517491_167005389_n.jpg

I honestly don't know why the 1st owner bought those ugly rims. But I got the stock wheels off him so will put them on :)

382366_10150447232452329_562992328_10517498_13439238_n.jpg

engine bay

382365_10150359097631121_645081120_8355496_1315349032_n.jpg

307747_10150359097701121_645081120_8355497_1560808671_n.jpg

Will post up more photos of the exteiror and interior soon.

I am thinking of selling around 27k mark considering the car itself was 100% genuine to start with, low mileage and all mods are brand new jap brand. Also with rego till march 2012. PM me if you are interested. Thanks

Edited by G0Z1LLAAAAA34
Link to comment
https://www.sau.com.au/forums/topic/383758-~eoi~-adm-s15-spec-s/
Share on other sites

  • 3 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 2 months later...

LOL Dude....looks like whoever bought your car has f**ked it up.

http://www.carsales.com.au/private/details/nissan-200sx-2001-12581653?base=1216&vertical=Car&cr=7&eapi=2&__N=4294739625 1246 1247 1252 1282 4294963846 4294963493 898 1216&silo=Stock&Range=Price:Min,Max~1&sort=default

Strong accident damage on left rear quarter. Rear bar also looks out of alignment. Front end also looks out of alignment. Hasnotbeenfixedproperly/10

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...