Jump to content
SAU Community

Nsw 18" Black Drift Teks And Federal Semi Slicks!

WAG.00N
 Share

Recommended Posts

WAG.00N Enthusiast

WAG.00N

Posted
Posted

Hey guys.

I was hoping to just sell the rear rims and all tyres but to make it easier for someone I'll sell all four wheels and tyres so you can just bolt them up.

They are 18x 8.5 et34 fronts and 18x9.5 rears. They are 4 and 5 stud and are pretty much brand new cost 1200 bux

The tyres are federal 595rsr's rears are 255/35/18 and fronts 235/40/18 and have only done 1 track day.  Cost $1200

Reason for selling is cause I want to run 8.5 all round to suit some tyres I can get.

$1400 for the lot (you save $1000 bux and i loose $1000 bux)

MSG or call Alex on 0415 292 220

Remember these wheels are nearly brand new!

I'm in concord nsw 2137

 

 

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sonicii
      Water pump replacement - Sydney region

      By sonicii · Posted

      There isn't that many cars yet that are using electric coolant pumps, but they are slowly becoming more common, especially in the euro brands.  back in 2009, they were quite rare, pretty much all were either timing chain or accessory belt driven. That said, the VQ37VHR isn't an uncommon engine, so any decent mechanic should be able to replace the water pump.  I don't live in NSW, so can't make any suggestions.
    • GTSBoy
      Can someone tell me what this part is for? Someone duct taped it.

      By GTSBoy · Posted

      I do not think that the return pipe could be the cause of your particular troubles, unless perchance it is leaking in a lot of unfiltered and unmetered air (assuming your ECU is still using AFMs). And then it could be very bad, but it shouldn't prevent you making boost. Blow then engine up from running lean? Sure. But it would make boost. You really needed to disconnect this thing from the turbo inlets and close those inlet ports off a year ago, and you should do it now.
    • GTSBoy
      Can someone tell me what this part is for? Someone duct taped it.

      By GTSBoy · Posted

      Pressure Ratio = 2. ie, 1 bar of boost (assuming 1 bat absolute pressure at the compressor inlet). This is relevant because compressor maps do not have "boost" up the y-axis. They have pressure ratio.
    • kevboost7
      Can someone tell me what this part is for? Someone duct taped it.

      By kevboost7 · Posted

      Revisiting this thread again x2... 1 year later. This car has been an ongoing project between life. But, I never removed the re-circ pipe. I know, shame on me. But since then, i took it to get tuned and only making about 280hp (lame) and i'm chasing a boost issue where the car wont boost past 7-8psi. Mac valve installed. Haltech Platinum pro with the map sensor.  This is the first time i've tackled the turbo side of things, but i have that side somewhat taken apart to chase the waste gate vacuum lines. And noticed this stupid pipe again. I'm peicing together the puzzle and @GTSBoy mentioned that it was a big vaccuum chamber and said a bunch of car math stuff that I couldn't quite follow the car math (im trying). You guys think this would be the culprit? between rotting vacuum hoses?  i'm making a DIY boost leak tester this weekend. 
    • kevboost7
      Can someone tell me what this part is for? Someone duct taped it.

      By kevboost7 · Posted

      What is PR2?
×
×
  • Create New...