Jump to content
SAU Community

Recommended Posts

Hey guys, I've tried searching the internet for some problems I'm having with my R32 GTR, I'm sort of new and still learning alot of things go easy haha.

Ive laid underneath my car and i can see the hicas lockbar all hooked, However if i take a corner hard , not so hard that im throwing the weightt of the car around it, But more like taking it fast with a little bit of angle which a gtr should manage .. The back end seems to kick out and it sort of feels like its trying to correct the steering .. But the back end just ends up kicking out a little bit . Is this normal or should i be checking things? Sorry if this sounds stupid I dont know much about the rest of the system except whats in the engine & bay itself lol.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/384700-hicas-lockbar-r32gtr/
Share on other sites

The 3 things that go and cause the issue you are describing are:

The outer ball joint that's pressed into the knuckle

The inner ball joint on the tie rods

The subframe bushes (but that feels more like the back end is flopping about than actually trying to steer)

Most people with this issue find it's the outer ball joint, on my car the inner went and the outers were fine. It doesn't take much play for it to start feeling very unsettled.

The 3 things that go and cause the issue you are describing are:

The outer ball joint that's pressed into the knuckle

The inner ball joint on the tie rods

The subframe bushes (but that feels more like the back end is flopping about than actually trying to steer)

Most people with this issue find it's the outer ball joint, on my car the inner went and the outers were fine. It doesn't take much play for it to start feeling very unsettled.

Hey , thanks for the reply . How can i test these things out? Because i grabbed each side and gave it a pretty good shaking i couldnt really see any movement or feel anything . Should i get it up on a hoist/jack and try it? Or is it worth just buying a new bar. Cheers

You really need to put a bit of force on the wheel to move it enough to see if there's a problem as you are pushing against the rest of the bushes in the rear suspension. You need to get the wheels off the ground and get under the car to see where the movement is when you are putting force on the wheels

No need to replace the lock bar. It's a bit of pipe with 2 tabs for the bolts and 2 threaded bungs for the tie rods. Nothing to go wrong.

You really need to put a bit of force on the wheel to move it enough to see if there's a problem as you are pushing against the rest of the bushes in the rear suspension. You need to get the wheels off the ground and get under the car to see where the movement is when you are putting force on the wheels

No need to replace the lock bar. It's a bit of pipe with 2 tabs for the bolts and 2 threaded bungs for the tie rods. Nothing to go wrong.

Thanks mate Will check it out , Havnt had time lately

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...