Jump to content
SAU Community

Rb26 Head Full Reco, Gtr Parts, Rb25 321 Stainless Manifold

Irwin123
 Share

Recommended Posts

Irwin123 Collaborator

Irwin123

Posted
Posted

Time to let this stuff go, going to uni next year, car will have to wait....

Rb26 head, has had a full reco:

-pressure test

-Overhauled multi valve surface ground

-Hardness tested

-Seat valve guides

-Adjust Valve clearances

-18 new shims

-12 Valve guides

performance valve springs fitted, comes with standard ones too

Spool head drain kit installed, brand new, comes with the whole kit: http://www.spoolimpo...d-oil-drain-kit

Full genuine nissan gasket kit included, valve stem seals used in the head

$2600 posted to an e-go depot near you!

The reco cost half that amount alone, see attatched for copy of invoice

post-74083-0-39278500-1325063462_thumb.jpg post-74083-0-25884800-1325063486_thumb.jpg post-74083-0-49238100-1325063511_thumb.jpg post-74083-0-77932500-1325063534_thumb.jpg post-74083-0-84954900-1325063558_thumb.jpg post-74083-0-57083300-1325064362_thumb.jpg

Rb25 321 stainless hi mount manifold:

Brand new, brought but keeping low mount, comes with gaskets, 2.6mm thick 321 stainless, 12mm thick flanges, not cheap ebay crap

$450 posted to your nearest e-go depot!

post-74083-0-18718100-1325063644_thumb.jpg post-74083-0-71388500-1325063653_thumb.jpg

Rb oil pump, was told it was rb26 $125

post-74083-0-47190200-1325063770_thumb.jpg

2x RB26/30 timing belts, one used for 30 min, one for 500ks $25 each or both for $40

post-74083-0-11772100-1325063836_thumb.jpg

Rb26 Harmonic Balancer $125

post-74083-0-42946200-1325063895_thumb.jpg post-74083-0-35667600-1325063913_thumb.jpg post-74083-0-41951400-1325063930_thumb.jpg post-74083-0-74622900-1325063949_thumb.jpg

Rb26 throttle cable $100

post-74083-0-54578600-1325063847_thumb.jpg

Can supply more details / pictures of anything

Best to send me a msg or give me a call on: 0407323643

friction_point Collaborator

friction_point

Posted
Posted

Long shot, but.....willing to separate the cam covers, valley cover and cam gear cover? If so, i'll take them :)

Cheers mate

friction_point Collaborator

friction_point

Posted
Posted

Sorry mate, not keen to split it yet, ill let you know if someone takes the bare head though! :)

Cheers, Chris

All good Chris, let me know.

Cheers thumbsup.gif

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...