Jump to content
SAU Community

Recommended Posts

just go to your local exhaust shop and ask them what extractors they can get.

oh and FYI, extractors won't do much for fuel economy. in a lot of cases they will do bugger all, or make it worse. they generally only make a difference to power at the higher end of the rev range, at the expense of a bit of low end.

it may be worth looking at other, cheaper things to try and improve fuel economy. check your o2 sensor, clean your AFM, take note of how long the car takes to warm up (if it takes more than 5 mins or a few kms of driving to warm up, or doesn't warm up to the middle of the gauge, then the thermostat is shot and replacing it will improve your economy) and most importantly, examine your driving style. if you floor it everytime you take off then you aren't helping the situation.

it's also worth pointing out that spending a few hundred dollars to TRY and get better economy is somewhat counter productive. lets say for example that you spend $300 on extractors and it only gives you a 10% increase in economy (which is a reasonable figure), you will only save $3 a week, so it will take you nearly 2 years before you have saved enough to pay for the extractors. what sort of economy are you getting?

ive cleaned both, run a high flow filter and cold air intake,, and 5w 30 oil, thinest that is practical to run, drive it like a granny, and im not nesacerally after the money back id just like to make the lack of power more liveable and keep the same economy if not improve it, after all number to is crushed to allow number three to run on the standard manifold, and i was more after recomendations for brands, sorry for not clarifying

most major brands are all reasonable quality. if you talk to enough people you will hear that every brand is crap, and that every brand is great. you are actually best looking on a lancer forum and seeing what they recommend. what brand works well on one car might not work as another brand on another car, so any advice you get from what works well on a skyline might not be true for on a lancer.

i've used genie and pacemaker headers with no issues in the past.

i should also note that there are certain cars where aftermarket headers make next to no difference in power. v6 magnas are a great example of this. the reason being that the cams are a bigger restriction than the headers. so gains will be minimal. having said that, on something like a SSS pulsar they make a big difference. also i've driven a lancer and they aren't that bad of a car power wise. maybe yours has a bigger issue, such as low compression or a dodgy fuel pump or clogged injectors (which a bottle of injector cleaner won't fix), or possibly even a blocked cat. not trying to talk you out of getting headers, just don't want you to be let down by the possible lack of gains if there is something else going on.

i have been tossing up those options of dirty/blocked parts, as it was driven extremely sedately when my mother owned it and runs better when it gets a bit of a rev or run injector cleaner through it, how would i go about cleaning these items

i should also note that there are certain cars where aftermarket headers make next to no difference in power. v6 magnas are a great example of this. the reason being that the cams are a bigger restriction than the headers. so gains will be minimal. .

At the risk of derailing this thread, and admitting that I was once a Magna tragic, I have to ask whether you tried the muffler upgrade? At the time I had my TH, the word on the street was that the rear muffler was a fairly m,ajor source of restriction, and replacing it with a bigger (not necessarily a ricey fart cannon) made a reasonable difference (around 10-12kW IIRC in the 3.5 TH). Never ended up changing mine (couldn't see the sense in hotting up a Magna) but there seemed to be a few people claiming it made a reasonable difference. Interesting to hear about the extractors though. At the time I got mine (early 2000) there weren't any off the shelf units, and my exhaust guy offered to make a set of stainless extractors for $500. Again, I couldn't justify spoending those $$ on the boat.

Normal programming will resume now.

Possibly - as Marc said it comes down to each car's areas of weakness. In the case of the Magna, the rear muffler was quite restrictive to keep them quiet (at the time they were reknowned for very low NVH levels compared to other cars in the class). If you're going for a less restrictive muffler, then larger volume tends to help keep the noise down while still flowing OK. Juet be careful you don't end up with something droney. Talk to the Lancer guys to find out what results others have had (just be prepared to wade through the stories of how a canon and shiny 4" exhaust turned a stock lancer into a GTR killah)

At any rate, I think on a 1.8 lancer, any exhaust changes will only have a marginal effect, and the benefits (if any) will most likely only be there at higher revs (ie peak power where flow will be highest), not for normaly day to day driving.

What do you fill up with? And what kind of economy are we talking about here? Auto or manual?

I have a daily Mazda 323, it's a 1.8. Manual. Filled up last night, and calculated 6.7 litres per 100 km. that's comuting, but being holidays traffic isn't bad. I use 95 at the pump, and have increased the static timing to compensate, to the point where I don't have pre det. I also removed the centre muffler, not cause full hectic, but cause it was forever leaking. Made nil difference in econ.

Also noticed you live in tassie. Roads can be pretty mountainous round those parts, so factor that into your economy. Other things that come to mind, do you do lost of short trips? That increases fuel use. Check your idle is within manufacturers stds, adjust if needed. Other than that, what Marc said about afm and O2 sensor.

At the risk of derailing this thread, and admitting that I was once a Magna tragic, I have to ask whether you tried the muffler upgrade? At the time I had my TH, the word on the street was that the rear muffler was a fairly m,ajor source of restriction, and replacing it with a bigger (not necessarily a ricey fart cannon) made a reasonable difference (around 10-12kW IIRC in the 3.5 TH). Never ended up changing mine (couldn't see the sense in hotting up a Magna) but there seemed to be a few people claiming it made a reasonable difference. Interesting to hear about the extractors though. At the time I got mine (early 2000) there weren't any off the shelf units, and my exhaust guy offered to make a set of stainless extractors for $500. Again, I couldn't justify spoending those $$ on the boat.

Normal programming will resume now.

yeah i did. mine was also a TH and i put a lukey rear muffler on and it made a difference. then i put a redback mid section on and it made a difference too. extractors did bugger all though. and yeah, up to around 10kw is pretty much spot on.

on average on good 91 i'll get 7-8ish per hundred, 6.5 if i get a really good batch of fuel, its manual, and its i have been tossing up that the timings out cause it does run a little rich, i've checked plug gap etc so

that is pretty darn good economy. you won't get much better than that. the best i've ever gotten out of the missus SSS is 6.5L/100kms on the highway (generally around the 7 to 8L/100kms on the highway. round town i generally get 10 to 11L/100kms out of it (and about 14L/100kms out of my vt wagon around town and 9L/100kms on the highway), but that is a lot of short trips (so car runs on cold start enrichment most of the time) and stop/start driving, so poor economy is to be expected.

if you do extractors then you would want to do a cat back exhaust to make the most of it. the power gains from doing this would be in the range of 5 to 10kw, but that will be more at the top end of the rev range. the low to mid range won't increase much, or may even drop a little bit in the lower rev range.

it really does sound like you have unrealistic expectations from a 4 cylinder car though. as i said in an earlier post, i've driven a 1.8L lancer and they aren't bad to drive as far as power goes. sure the don't have the low down pull of a larger motor, but they are far from lacking (unless there is a mechanical issue, but from your fuel economy i don't think there is). any mods you do to increase power will only gain you about 10% more power, most of it at the higher end of the rev range. so not really the sort of change that it sounds like you are after. about the only thing that would give you the sort of low to mid range power gains is bolting a turbo to it.

I have never heard of anyone going backwards with extractors, unless you were to fit ones that didnt suit the particular motor (i,e overly large primaries etc). might not give a huge increase in power but should make the motor considerably more efficient.

Pacemaker do a 4 into 1 set for about 400 bucks.

OP: stop thrashing the shit out of it!

BTW the thought of modding a Magna is laughable. Worst aussie family car i've driven, i'd rather get around in a VN!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I did end up getting it sorted, as GTSBoy said, there was a corroded connection and wire that needed to be replaced. I ended up taking out the light assembly, giving everything a good clean and re-soldered the old joints, and it came out good.
    • Wow, thanks for your help guys 🙏. I really appreciate it. Thanks @Rezz, if i fail finding any new or used, full or partial set of original Stage carpets i will come back to you for sure 😉 Explenation is right there, i just missed it 🤦‍♂️. Thanks for pointing out. @soviet_merlin in the meantime, I received a reply from nengun, and i quote: "Thanks for your message and interest in Nengun. KG4900 is for the full set of floor mats, while KG4911 is only the Driver's Floor Mat. FR, RH means Front Right Hand Side. All the Full Set options are now discontinued. However, the Driver's Floor Mat options are still available according to the latest information available to us. We do not know what the differences would be, but if you only want the one mat, we can certainly see what we can find out for you". Interesting. It seems they still have some "new old stock" that Duncan mentioned 🤔. I wonder if they can provide any photos......And i also just realized that amayama have G4900 sets. I'm tempted too. 
    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
×
×
  • Create New...