Jump to content
SAU Community

S1 C34 Upgrade Goodies

4bidn1
 Share

Recommended Posts

4bidn1 Mentor

4bidn1

Posted
  • Author
Posted
[/color]6221731']

Emanage sold

coil packs sold

550cc highflow injectors still avalible $400 $350 still avalible

S1 mv shift kitted and serviced auro trans 315 kw rating all recipts $450 ono (you cant even get the shift kit fitted for that much) still avalible

S2 rear corner tail lights pair $100 still avalible

S1 rs4 front mesh grill with rs badge $100 still avalible

stagra tein coil overs front no leaks damper adjustable $200.still avalible

R34 neo standard turbo good condition $250 $200 still avalible

cheers jase

Springsteen pm replied

  • 2 weeks later...
  • 5 months later...
  • 2 weeks later...
whitenight27 Proficient

whitenight27

Posted
Posted (edited)

Mines factory chipped. so boost cut rev limiter speed limiter removed some times extra fuel /air depending on what was ordered you can chase what was done by the individual numbers on the gold mines plaque

i know this might have been a while ago but the mines ecu do u know what the ecu numb was?

i just got 1 off a guy hear in perth for $20 as he was not shore if it fitted the stagea or not. it just came with his car.

i am only running it to remove the boost/ speed cut and maby slight better tune what ever it has just for a short time as the car has new motor plans

i have tryed it in my s1 and it runs and drives no prob at all. and with looking up the mines info off the plaque who can tell me about what was done?

Edited by whitenight27
  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...