Jump to content
SAU Community

Recommended Posts

Finally decided its time to let my pride and joy go, have got this advertised on carsales, but I thought id put it on here aswell. Would much rather know that it was going to a fellow enthusiast :)

Basic details, has done 126000 on the body, motor has done around the 150 mark, but it is still healthy, no sign of blowby etc. This car was originally non-turbo to begin with and one thing led to another and it ended up with a genuine S1 turbo long motor and gearbox. All the required upgrades including fuel system and brakes were done aswell so its basically a turbo car minus the 5stud conversion!

Copied from carsales.com.au add, also if your looking for photos they will be on this add when it gets approved (will post link here once its done);

Up for sale I have my pride and joy 1994 Series 1 R33 Nissan Skyline. I am the 1st Australian Owner since it was imported back in 2007.

All the basic modifications have been done aswell as a few extras including;

-Front Mount Intercooler

-K&N Pod filter within cold air intake enclosure

-Larger T04E Turbo @15PSI

-Greddy Style front facing intake plenum

-TurboSmart Supersonic single port Blow Off Valve

-3" STREET LEGAL JASMA (impul) turbo-back exhaust

-Walbro in-tank fuel pump with SARD rising rate fuel pressure regulator

-Microtech LT-12S Engine Management system (with hand controller) tuned @ 200kw atw

-Tein SuperStreet Height and damper adjustable coilovers

-Front & Rear strut braces

-HICAS lockout bar

-A-Pillar Boost and Air/Fuel ratio gauges in gauge pod

-18" Alloys

-Jensen Touch Screen DVD head unit

-Earthquake 12" 1000W Sub

Only serviced with Royal Purple fully synthetic oil, has recently had a full check over and everything on the car is mechanically A1

The few bad points are there is key marks on the passenger side spanning the front quarter, door and rear quarter panels. These may be able to be patched up by a specialist painter or completely resprayed, a few very minor dints in the rear driverside quarter panel, would be easily removed. The only signs of rust are a few spots on the roof, and very slight surface rust near the bonnet arms.

This car has not been in any accidents and is completely straight panel wise. All standard electrical features work, A/C has recently been re-gassed and works brilliantly.

Selling without an RWC, leaves you open on whether to keep it a street legal weapon or turn it into the ultimate track car. All the building blocks are here I have just run out of motivation to continue it on its journey

Asking for $8000 as is, no reasonable offers will be refused

Snap this up quick before its gone!

Link to comment
https://www.sau.com.au/forums/topic/389034-vic-1994-r33-gts-t/
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...