Jump to content
SAU Community

3Rd Annual Pre-Powercruise Dyno Day 18.02.12 Newcastle


Recommended Posts

Copied from another forum thanks :thumbsup:

It's that time again. The 3rd annual PRE-POWERCRUISE dyno day will be held Saturday the 18th of February

Will kick off at 8:30am at 4b ACTION Mitchell st Cardiff.

Come down and run your car so you know every thing is running sweet before you flog the car for 3 days at the big event. Or just come down to see what other cars make

Categories

4 cyl N/A - 4 cyl forced

6 cyl N/A - 6 cyl forced

8 cyl N/A - 8 cyl forced

FWD

HP per litre

Highest HP overall

Encouragement award

The dyno is a DYNO DYNAMIC 2WD dyno ( sorry all you AWD people)

There will be a trade stands from AUTOBAHN with all your performance parts and car care specials for sale, and a BBQ going all day.

Price is $60 for 3 power run and a print out of hp,kw,AFR,boost etc and a free sausage sizzle and can of drink

Please check your water and oil levels are topped up before your car gets run up

Hope to see every one there

Link to Facebook page

http://www.facebook....25744700793397/

best bet to get in and pay your money early they only have 50 spots.

  • 4 weeks later...

I was the first up on the Dyno managed a 190rwkw at 13psi untuned with healthy afr's so was pretty happy, specially since my first Dyno run at hunter awd dyno was 130kw :(Was good to see some other skylines, majority were r32's even 1 running a 1jz, good day for along as I was there. A few common skyline problems managed to find themselves but I think faulty coils may be the cause of a low reading for a weapon of a 34,and rb20's with a little heat soak. Other Cars were a decent amount of v8 utes, a few Silvia boys and xr6t with 350kw boiling coolant , which was cool to see in the overflow. Big thanks to the boys, even allowing me to run shotgun to pump some more boost in :) hope some people got photos.



  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...