Jump to content
SAU Community

Info on a Roll Cage for R32 GTR

DR.ZOIDBERG
 Share

Recommended Posts

DR.ZOIDBERG Proficient

DR.ZOIDBERG

Posted
Posted

Hey

Can anyone tell me if you can get a Roll Cage (full cage 6 point+) to fit a R32 GTR with out modding anything at all, like most GTR R32's I have seen have rear seat removed to fit cage and some have cut dashes door trims etc to fit them too.

Im after a cage for my R32 GTR that doesnt require any of that, I want to be able to keep rear seat in and not cut anything or mod anything at all, I know I will have to bolt cage to car floor but dont want to do anything eles if you get me.

If anyone can help me out on were to get one or if anyone has one forsale that meets what im after PM or EMAIL me please, Im after either Jap cage or Australian Cage and it does not have to meet australian racing rules etc

If anyone can help me please

Im in QLD Gold Coast

Thanks

CHASP

Link to comment
https://www.sau.com.au/forums/topic/39122-info-on-a-roll-cage-for-r32-gtr/
Share on other sites
R32GTRRR Explorer

R32GTRRR

Posted
Posted

Ive got a 6point rollcage that was previously in my old R32 GTR

let me know if ur interested and if you want Pics!!

Regards

David

[email protected]

Hey

Can anyone tell me if you can get a Roll Cage (full cage 6 point+) to fit a R32 GTR with out modding anything at all, like most GTR R32's I have seen have rear seat removed to fit cage and some have cut dashes door trims etc to fit them too.

Im after a cage for my R32 GTR that doesnt require any of that, I want to be able to keep rear seat in and not cut anything or mod anything at all, I know I will have to bolt cage to car floor but dont want to do anything eles if you get me.

If anyone can help me out on were to get one or if anyone has one forsale that meets what im after PM or EMAIL me please, Im after either Jap cage or Australian Cage and it does not have to meet australian racing rules etc

If anyone can help me please

Im in QLD Gold Coast

Thanks

CHASP

Duncan Grand Master

Duncan

Posted
Posted

yes you will need to get rid of back seats for any decent cage, including half cage. Yes you will need to cut dash, roof and door trims.

If you don't need it for CAMS, I don't think you really want to go thru all the hassle....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
    • GTSBoy
      R34 25GT Engine Light 21

      By GTSBoy · Posted

      Could be correct. Meter might be that far out. Compare against a known 5 ohm 1% resistor.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap.  (edit: I went out and did it right now, the line I had chosen did appear to have no vacuum on it, it used to go to the front of the intake, I've now completely blocked that one off at the bracket that holds several vacuum lines by the firewall.  I T'd into the vacuum line that goes from that bracket to the vacuum pump at the front of the car, but no change in the MAP readings).  Using the new vacuum line that has obvious vacuum on the hose, im still only getting readings between -6.0 and -5.2.  I'm wondering why the ECU was detecting -5.3 when nothing was connected to the MAP nipple and ECU MAP selected as the source. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
×
×
  • Create New...