Jump to content
SAU Community

Recommended Posts

I've got an issue with my R33 GTST. It doesn't always want to start when I turn the key. It will crank, but not always start immediately the first time like it should. Sometimes it will take up to 10 turns of the key before it will eventually turn over. I've taken the starter motor out and cleaned all the connections, including all wires that connect to the motor itself. Done this 3 times now and it's still doing the same thing...not always starting first go. I don't know if this issue is the starter motor or the wiring, as sometimes it will start 3 times in a row, first time every time, but then it just stops and it'll take up to 10 goes.

Has this happened to anyone else? Can anyone here help me and know if I need a new starter motor or it's the wiring that's the issue ???

Link to comment
https://www.sau.com.au/forums/topic/392267-intermittent-starter-motor/
Share on other sites

If you are turning the key, and the engine turns over, the starter motor should be fine (unless it is turning rather slowly).

How recent is your battery? have someone check the battery volts as you crank the engine (just from the jumping point in the engine bay should be fine), if the voltage is dropping too much then it may be stopping the electronics from working properly.

Otherwise, if battery/ starter are fine, start looking at either fuel or spark.

If your starter motor turns every time, it's not the problem. The f**king battery in my car is as big as a tissue box if not smaller. I get 7v when cranking but it still starts... Try another battery, if nothing then there is another problem, which could be easy or.a pain to find.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...