Jump to content
SAU Community

Recommended Posts

Hi all, am clearing out the garage of some unwanted stuff.

All items are pick-up preferred from Warrnambool Vic. Can post smaller stuff at buyers expense. Can also deliver or meet buyer half way at buyers expense.

PM, post here or text 04 3774 5147 for more information any questions etc.

I am unable to post photos at this time as the camera I have takes 4mb+ photos. I can however MMS photos.

1. Assorted EMPTY tool cases for the following Sidchrome 3/8" and 1/2" socket sets, Repco 1/4" socket set, Stanley screwdriver set, EMPTY spanner rolls for Sidchrome ring-open-end, ring, double-open-end spanner sets.

>>>>ALL CASES ARE EMPTY<<<<<

$20 the lot

2. Nakamachi? CD player, came with car, working condition.

$5

3. Exedy clutch kit, good condition, only removed/replaced due to noisy spigot bush and didn't ant to get caught out. Part number on pressure plate is NSC 534. Came out of R33 GTS.

$50

4. Stock coils. Suit diagnosing dead miss etc. Out of series 1 R33 GTS

$10

5. Stock dump/front pipe suit R33 GTST

$10

6. Stock thermofan, removed to fit FMIC, HAS BEEN MODIFIED

$10

7. Stock Jecs fuel pump from R33 GTS, unknown condition

$5

8. Stock intake/rubber pipe and crossover pipe

$10

9. Genuine Mazda RX8 rotary oil and filter suit RX8

$20

10. Speco Meter oil pressure gauge, think it's 2.5", has sender

$10

11. Stock Mazda RX8 spare wheel, unused, has leather cover

$10

12. Ryobi mitre saw, part number EMS 1221, 1200w, 210mm, braely used, still in box with accessories. Paid $130

$30

13. Stock springs and shocks from R33 GTS

$20 the lot

14. Assorted EMPTY Snap-On tool cases, part numbers CTSA561CL, CTSA561, CTA4850, CDRA6850, suits 1/2" electric rattle gun, cordless drill, cordless bit-driver, and 3/8" rattle gun CASES ARE EMPTY

$20 the lot

15. Stock swaybars from R33 GTS

$20 pair

16. 2 BCT S600 tyres, 205/55/R16, flat spotted, camber wear, suit skids

$20 pair

Will post photos if I can find a camera that takes a smaller file size. Will also add itmes as I find them.

  • 4 weeks later...

Also for sale:

2 Pioneer GMD7400M monoblock amplifiers

2 Eclipse SW6010 10" subwoofers

Currently in car and can be heard running, one sub has had the surround re-glued to the basket over a year ago, good working order had no issues since.

Selling as a package for $400, pick-up or arrange a meeting place etc only.

2 subs and 2 amps as pictured:

(sorry for the poor picture)

post-74990-0-90776000-1332545874_thumb.jpg

  • 2 weeks later...
  • 1 month later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...