Jump to content
SAU Community

Recommended Posts

nah dont know specs, its a T04E, is on an HKS manifold with HKS ex gate so is pretty big. its laggy but not too bad. it starts making boost around 2500 but thats like 01-0.2 bar but gets up to my 08.bar at around 4000rpm......

are you running a metal head gasket or forged pistons to take it to 18psi? i know their efficiency range is around 18-22psi but i cant take mine that far with stock injectors and internals....

I will run RX7 injectors, internals are supposed to be good for 250rwkw, i would likr to get 230rwkw and will run up to 18psi for the steet. Mine is a TO4e as well, its the smallest fo the T04's they make and is not that big compared to the others.

Once I have everythink runnikng i will probably get another engine built a bit stronger depending on how it runs. Metal head gaskets are not required as much on RB20's due to their lower compression and it it is tuned right with no detonation it should be fine, hopefully.

217KW SPECS

FMIC

3.5" EXHAUST FROM TURBO

VG30 TURBO

1 BAR BOOST

S-AFC

BOSCH 910 FUEL PUMP

HKS CAM GEARS

ADVANCED IGN TIMING

HIGH OCTANE FUEL (70% ULTIMATE + 30% TOLUENE)

DCS HEAVY DUTY SINGLE PLATE

206KW SPECS

FMIC

3.5" EXHAUST FROM TURBO

VG30 TURBO

1 BAR BOOST

S-AFC

BOSCH 910 FUEL PUMP

Don't forget that the clutch makes a big difference as you have to be able to transfer the power to the wheels. We drove my mates car on the road and the clutch seemed OK but when we dynoed it it only made 213rwkw then we replaced the clutch and now it makes 231rwkw, a similar thing happened to me now my car feels a lot quicker as all my power is getting to the wheels.

I will post the power figure with the cam gears and normal Ultimate fuel once I have it de-tuned for daily use....still have a bit of the good fuel in the tank so I want to use it up :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...