Jump to content
SAU Community

Recommended Posts

Hi mate,

have i missed the price somewhere? I am geniunely interested but need alot of questions answered.

How did the piston crack look/where? is there actual compression readings across the cylinders?

I have just been quoted ~$2000 to exchange a motor across 3 workshops across sydney. Is the quote to fix the

piston only or include removal and install of the motor?

Will one piston just be replaced for $1300. Who will be doing this? will headgasket be reused? choice of bearings?

Can this person your using rebuild this motor to my spec seeing its going to be apart already?. No point pm'ing as

im pretty sure theres plenty of other people asking the same questions.

Cheers

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

Very valid questions, and your right its very good for everyone to know.

compression across the rest of the motor is outstanding, 170psi, 170, 168, 170, 170 and then cylinder #6 35psi and 50psi on a wet test. first time i did the tests myself i got in the vicinity of 150 but then i noticed my gauge was a little screwed, so i just had it check properly, and then checked again myself with a new gauge to verify the 170psi readings.

The crack is more of a fracture in piston #6, and the rings which were giving the low reading , The valves and cylinder are fine, not bent or anything.

The cause of the problem was a faulty boost crontroller solenoid ( $30 - $50 ), spiking of the boost i was told led to this.

well yes i mean it works out perfectely for anyone looking to do a rebuild anyway or who has a engine ready for a gtr or something similar...

my quote and intentions were to return the car to its normal state with all the mods still ofcourse.

so anyways... basically pull apart the pistons and replace anything surrounding that is needed e.g rings , im not 100% certain what bearings would be used. im pretty sure i would have sourced some decent looking used parts where i could, reason being it was fine handling the power if it wasn't for the boost controller solenoid. i know people may disagree but sometimes money isnt always available when needed.

A close friend quoted to do this for me if i chose to go down the path myself,

i was going to forge the motor if it didn't sell but with certain issues at the this point, im not going to anymore. im going to sell/swap the way it is.

I hope this helps and havn't missed anything. if you want to talk further PM me ill give you my phone number.

alright fair enough, bad luck with the solenoid mate.

check your inbox i sent you some more details, ive got some parts from my previous r33.

let me know also when your free tomorrow

Bump...

Should be gone shortly, haven't been in hurry lately so i apologise to the guys wanting to come out just been very busy.

Always has been a top car to drive, especially down to canberra once a week for a few months straight. receipts for work and dyno papers to come with, always been looked after. really a shame that a small $30 solenoid caused this. A couple of SAU members have had the car checked also and have told me their quotes are pretty much the same as mine, give or take a few hundred.. probably give more so :)

Just have some common sense, if your going to offer me 10k think about it.. your getting a 12k Gtr ...please save your time and dont have sulk when im an asshole back. :)

losing the company vehicle .....

willing to put a few thousands on top for a swap.

otherwise i got no choice but repair and wait close to a month for it to be done through my mechanic.

Edited by binga85

Update

It's in the Workshop now!

Might be getting fixed if i can get it done quicker than 3-4 weeks. otherwise still selling as is.

Inspections may be a little harder now, however PM and we can sort something out possibly over the weekends as during the week will be very hard now.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
    • It sounds like you want what the Toyota Landcruisers have for their roof racks. Wanna know what you end up with? Rust holes in the roof, and water everywhere...
    • Discovered today that if I select reverse first and take my foot off the brake, then select drive, the drive indicator light works and so does the tiptronic gear indicator. 
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Does anyone here have any ideas?   Cheers guys
×
×
  • Create New...