Jump to content
SAU Community

Recommended Posts

R31 WITH ADDITIONAL RB20DET AND ALL CONVERSION BITS.

i have for sale a r31 sedan rb30 auto

the good

very reliable daily with standard motor just has exhaust and pod filter boxed off properly.

i no the history of this car for last 8 years and have kept up servicing of engine including water pump timing belt etc.

interior has couple things missing but still tidy.

i also have a redtop rb20det and 5speed box from another r31 with 100% all the things you would need to do the conversion.

it would come with a separate diff with minispool and front cross member holding upgraded suspention swaybars etc.

i could also chuck in the 15 inch alloys n tyres if the price is right .plus spare doors, seats pannels, lights etc

the car could be turned into capable drifter even with the 3l in it.

the bad

car has peeling paint and few dents (have the panels to replace, to make it straight)

i dont have time to do conversion cause i have too many other cars sucking my time away

price is 3300 ono for the lot, might sound a bit steep but for what ya getting its cheap. and thers no money to spend.

contact Ken on 0413638772.

also have HD HOLDEN sedan all original 179hp 2 speed powerglide good restorer 2500 ono

  • 2 weeks later...
  • 4 weeks later...
  • 4 weeks later...
  • 3 weeks later...

last chance to buy this before i consider doin the conversion myself. got some spare time now.

$2400 for lot or $1600 for motor package and everything r31 i have laying around. thats alot.

  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
    • Appreciate everything guys. I did go ahead and get an alignment... most of my complains are solved. Car is not perfect, but it's good enough. If I notice uneven tire wear or anything I'll just take everything back to stock.  Thanks again!
    • They still have not shipped the 550cc injectors as they weren't in stock, so in theory I could ask to get the 440cc ones instead, if those work better in my scenario. They're the same price so really shouldn't be an issue. Unfortunately I am not so knowledgeable in most parts of tuning so I wasn't sure what's best to choose between the two. 440cc ones are the lowest they have (not in stock, but available to buy nonetheless).
×
×
  • Create New...