Jump to content
SAU Community

Recommended Posts

Purchased of the r31skyline forums about 10/11 months ago.

Has been a complete pleasure owning this car. Given me no troubles at all.

Has reasonable power and sounds like an RB Should

Approx 210,000 on body - 90,000km on the motor

Serviced every 5000km

Resprayed in black with pearl, gorgeous colour.

New black carpets

Import front and rear seats - front drivers seat is electric

Top of the line viper alarm system with remote start - the remote for the remote start is broken. So it cant be used, unless you pay $400 for a new remote.

Its a ridiculous price so I purchased a standard remote instead.

Import projector headlamps

Peddars lowered suspension

Whiteline rear sway bar

Sportmaxx XXR02 wheels 16x8

Pioneer headunit

From the original for sale add:

Series 1 RB25DET engine and manual gearbox conversion done by mercury motorsport. (modplated and engineered)

Nismo heavy duty clutch

Custom one piece tail shaft and silhouette limited slip diff

Genuine HKS 2535 ball bearing turbo

Custom 3'' exhaust - twin tips

Front mount intercooler & GFB B.O.V

Apexi PowerFC with hand controller

Z32 airflow meter

Walbro fuel pump

Greddy electronic boost controller. High and low settings, 9psi and 14psi

Dyno sheets for 175kw on 9psi and 200kw atw on 12 psi

Currently tuned and running 14psi so probably another 10+kw or so more.

Injectors are stock 370cc and are pretty much maxed out on 14psi, currently on 90% duty cycle.

Has ran a 13.6 @ 105mph. Goes pretty good and that was a pretty slippery run.

The bad, unfortunately to pass a road worthy, the car will need to be raised in the rear.

Because its been sitting so low, the rear tyres have been chewed up pretty good.

Plenty of tread but its got deep groove marks.

The car will come with new Peddars standard height springs.

Swap them over, and get 2 new rear tyres.

Price $7500 - No RWC, No rego.

Car located in Townsville

Call me on 0413 524 083

u0oHD.jpg

JI11I.jpg

gkYWu.jpg

PrYud.jpg

mwlK2.jpg

H93X2.jpg

vjucd.jpg

Edited by privatealpha
Link to comment
https://www.sau.com.au/forums/topic/399976-qld-1990-r31-black-rb25-200kw/
Share on other sites

  • 9 months later...
Big Bump, Still for sale.

Will sell for $7000 includes 4 spare wheels. S13 wheels, all brand new tread.

Now with 740cc injectors and running 17/18 psi.

Not sure of power but now runs 13.3 @ 111mph. Shit time but great trap speed.

Roughly a mid 12 sec if you have the traction for it.

Located in Cairns.


uXRnjV3.jpg

X1J1nrf.jpg

Ld48UjY.jpg

CYTG6bD.jpg

Cr80SiM.jpg

ST7Rr.jpg

7V9ESbS.jpg
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...