Jump to content
SAU Community

Recommended Posts

AS STATED SHOW SOME INTEREST AND I WILL STRIP BUT PREFER WHOLE CAR GONE !

-ALL SUSPENSION UNTOUCHED JUST BODY DAMAGE !

-Had the thing for 6 months only been on the road for 2 weeks. Under went a FULL RWC at the pits not a dodgy mechanic. Has new bushes pretty much every where only nolathane, new upper inner ball joints, 4 rack ends, tie rods, wheel aligned 2 weeks ago and has 4 almost brand new tyres. Passed inspection no worries (made sure it was perfect)

-Crashed in the front pushed rad support back into engine sooo headlight, front bar, intercooler, rad support maybe radiator (still holding water and doesnt look bent) bonnet. thats what i can list as damaged off the top of my head

-rb20det 4wd motor. Runs well and goes very well has a RB25 turbo with steel wheel 20 acutator bolted to it

-17" sparco wheels 8" front 9" up front lowered with RSR springs and upgraded struts, m spec side skirts

-Did have FMIC but shes finished, Pod filter, have an adjustable bov but has blocked stock one for flutters :P

-obviously has the attessa system and it has a torque split controller

-3inch turbo back blitz exhaust, trust dump pipe

-650hp fuel pump, stock computer with assumming stock tune. pulls hard though for a lil 20

So as stated the suspension has been untouched. Buy something like this for 600 http://www.ebay.com....#ht_2084wt_1270

and then you would have a rare gts4 skyline front quarter panels are un damaged . or just pull it back off the be;ts and have no front bar, bonnet and lights. Im thinking of just this my self if i can find a cheap panel beater but if someone else wants it they are welcome to it. would make a shibby track/drift car

the car is a repairable write off any questions call 0459302735

Price for full car 2800...2100 if wheels are supplied. Front diff is a bit noisy when ran in 50 50 config but not in the attessa setup. 600 for both

you in melbourne? if not 3064 is my postcode what postage costs am i looking at?

Edited by ZILLR

Not in melbourne about 5hrs away could possibly meet halfway if i decide to strip if an extra 100 is given. postage id assume would be about 250

could do with a paint id say but yea there fine i would post. as stated may not strip just seeing if there is interest. will strip if motor/box is wanted

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...