Jump to content
SAU Community

Recommended Posts

Hi All,

Had an issue with my GTR last night.

Engine had a noticable miss while driving at approx 60km/h and then a few minutes later when I was stopped at the lights, I went to take off normally but the car was constantly bunny hopping and stalling and wouldnt actually drive more than a metre without sh*tting itself.

I could free rev it but as soon as i took my foot up off the clutch to take off it would stall or almost stall. Tried quite a few times.

I managed to limp it to the side of the road and then jiggled the rear AFM cable and the AFM itself as a first attempt to rectify and the car appeared to instantly start idling smoother and i could drive it again. But I dont know if this was just coincidence though.

Is there anything else I should be checking? It probably is the AFM or dirty AFM connection / plug - But what else could cause this behaviour?

The car used to have a different constant miss and lack of power which was caused by a worn out intake manifold gasket but this has since been rectified and is something different.

Previously, the car has had -

- Test for air leaks performed

- Replacement metal intake manifold gasket and hoses

- Replacement NGK Platinum PFR6A-11 plugs

- Coil packs checked - appear okay

- Rear air flow meter replaced (as previous air flow meter had a higher voltage and was causing the car to run a bit rich)

- Fuel filter replaced with Genuine Nissan - 16400-53J10

Doubt it would be a clutch issue but incase it helps diagnose, the car has also recently had -

- Stock dual mass flywheel reinstalled with Nismo clutch remaining in the car

- Replacement spiggot and thrust bearing

- Brake and clutch fluid topped up with Castrol Response Super DOT 4

Only things I did yesterday morning was put in Royal Purple HPS 10W40, replaced the oil filter with a genuine Nissan 15208-53J0A and also put some fuel injector cleaner into the fuel tank.

Will be aiming to get it to my mechanic tomorrow, but may be hard to reproduce the fault.

Any advice or info would be appreciated.

Cheers.

Edited by iwanta34gtr

sounds like afm bud. Also check you intercooler hoses for splits and cracks. The stock ones on mine developed a crack in them, but I also had a AFM die aswell.

Thanks mate, I will take a look at the cooler hoses - but I also have a gut feeling its the rear AFM fouling up again.

Fuel filter?

Thanks for the reply mate, but I have already changed the fuel filter with a genuine Nissan 16400-53J10 item.

Still appreciate your post and trying to help anyway.

Just had this happen on mine, was my lower AFM. I had the same thing with sputtering and bunnyhopping. I found that unplugging both afms should make the car idle a bit high but smoothly and plugging the AFM's back in should cause the problem to reappear.

I tried some AFM cleaner from supercheap but it didn't fix mine, contact cleaner should work as well.

Thanks guys. As the rear (top) AFM was a replacement from my mechanic, will be aiming to go back and get diagnosed / replacement today.

Also need to get the front AFM checked.

Will post results.

Update.

Took the car to my mechanic this afternoon and it spat out an air flow meter error code.

Replaced the rear air flow meter and cleaned the front one while we were at it - so far so good, touch wood.

Will see how it goes over the next few days.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...