Jump to content
SAU Community

Max Power (Kw) Output For N1 Oil Pump On A Rb26

loky
 Share

Recommended Posts

loky Proficient

loky

Posted
Posted

so i have been discussing this issue with friends and have gone out of my way to ask a few mechanis as well. i have been told the n1 pump break once you push them to 450 kws at the rears or more on a gtr.. now just want to get a few more answers on this issue.

do they break at 450 kw at the rear or at all four?

do they brake at a much lower power range?

and what the most you could push an n1 oil pump to?

thanks guys much appreciated!!

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

^ Yep. Because GTRs are not 4WD. They are RWD until ATTESA decides otherwise - and even then, it does not become a 50/50 split like a 4WD car (EVO/STI).

So most certainly not the same. Do some reading on ATTESA on this forum and become enlightened :thumbsup:

To the OP - N1 pumps, and any pump for that matter - can break @ 350rwkw if not treated correctly.

There is no set "figure" or power range. It's like asking how many people does it take to eat an apple - the question has no valid answer.

Closing as a result given such a question only ends in heresay.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      You are selling this? I have never bought something from marketplace...i dont know if i trust that enough. And the price is little bit "too" good...
    • Watermouse
      "Cheap" bolt on turbo on RB25DET NEO

      By Watermouse · Posted

      https://www.facebook.com/share/19kSVAc4tc/?mibextid=wwXIfr
    • Kinkstaah
      Airbox for +T

      By Kinkstaah · Posted

      It would be well worth deciding where you want to go and what you care about. Reliability of everything in a 34 drops MASSIVELY above the 300kw mark. Keeping everything going great at beyond that value will cost ten times the $. Clutches become shit, gearboxes (and engines/bottom ends) become consumable, traction becomes crap. The good news is looking legalish/actually being legal is slighly under the 300kw mark. I would make the assumption you want to ditch the stock plenum too and want to go a front facing unit of some description due to the cross flow. Do the bends on a return flow hurt? Not really. A couple of bends do make a difference but not nearly as much in a forced induction situation. Add 1psi of boost to overcome it. Nobody has ever gone and done a track session monitoring IAT then done a different session on a different intercooler and monitored IAT to see the difference here. All of the benefits here are likely in the "My engine is a forged consumable that I drive once a year because it needs a rebuild every year which takes 9 months of the year to complete" territory. It would be well worth deciding where you want to go and what you care about with this car.
    • GTSBoy
      Airbox for +T

      By GTSBoy · Posted

      By "reverse flow", do you mean "return flow"? Being the IC having a return pipe back behind the bumper reo, or similar? If so... I am currently making ~250 rwkW on a Neo at ~17-18 psi. With a return flow. There's nothing to indicate that it is costing me a lot of power at this level, and I would be surprised if I could not push it harder. True, I have not measured pressure drop across it or IAT changes, but the car does not seem upset about it in any way. I won't be bothering to look into it unless it starts giving trouble or doesn't respond to boost increases when I next put it on the dyno. FWIW, it was tuned with the boost controller off, so achieving ~15-16 psi on the wastegate spring alone, and it is noticeably quicker with the boost controller on and yielding a couple of extra pounds. Hence why I think it is doing OK. So, no, I would not arbitrarily say that return flows are restrictive. Yes, they are certainly restrictive if you're aiming for higher power levels. But I also think that the happy place for a street car is <300 rwkW anyway, so I'm not going to be aiming for power levels that would require me to change the inlet pipework. My car looks very stock, even though everything is different. The turbo and inlet pipes all look stock and run in the stock locations, The airbox looks stock (apart from the inlet being opened up). The turbo looks stock, because it's in the stock location, is the stock housings and can't really be seen anyway. It makes enough power to be good to drive, but won't raise eyebrows if I ever f**k up enough for the cops to lift the bonnet.
    • BuiltNotBought
      Airbox for +T

      By BuiltNotBought · Posted

      There is a guy who said he can weld me piping without having to cut chassis, maybe I do that ? Or do I just go reverse flow but isn’t reverse flow very limited once again? 
×
×
  • Create New...