Jump to content
SAU Community

Recommended Posts

Hey all well another r34 has been ramed up th arse by a stupid driver

It was well looked after still has top range hks zorst front mount amd shitty 18inch wheels

Was allways serviced with motul turbolite 4100 etc

Brand new tyres and heaps more ill post a betted thread when i get home but it is reparable write off

It even has nismo front pads just put in

Oviuosly no rwc or rego and will need to be payed for and picked up asap before insurance will by it

Offers over 2500 will be taken and yes it is a turbo neo rb25det 1999 model

Located on bendigo victoria

Call rossco on 0421506888 or text what eva

Once again will fix thead later soz hate using phone to post shit

Must sell within the week if posable i think asking price is verry fair thanks

Edited by cuttz

Doesn't look like much damage, easily fixable with a rear clip or even just pulling it back out with an auto robot.

Good deal, too bad you're not in Sydney, would have snapped it up for myself.

Thanks mate it just sold then anyway

Its not to bad it still drive nice tbey just did it as an economical loss

Anyways ITS SOLD

May have spoke to soon have both buyers stuffing me around

Untill i have cash in my hand its staying up for sale

My appoligys to ever rang or text me yesterday first with cash gets it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...