Jump to content
SAU Community

Anyone Interested In A Urethane Nismo V2 Front Bumper Group Buy?

Nightcrawler
 Share

Recommended Posts

Nightcrawler Grand Master

Nightcrawler

Posted
Posted

I have been looking all over for a Nismo front bar. Can't find one in Aus, so have been looking overseas. Shipping price alone on a single bar from the USA is around $500.

So I have been in contact with a guy in the USA who is willing to ship to Aus (ALL other sellers didn't even respond let alone give me a quote) on these bars:

http://www.ebay.com/itm/390396183055?item=390396183055&viewitem=&sspagename=ADME:X:eRTM:MOTORS:1123&vxp=mtr

Note that these are made of Urethane (like oem), so unlike even the genuine Nismo bars (which are made of fibreglass) these are extremely flexible and will not break. I have learnt my lesson with fibreglass bars - they just do not last. Yes the Nismo bars are a much higher quality and flexibility than other fibreglass bars, but I have still seen them crack.

So is anyone else keen if I buy a few of these suckers? Price at this stage delivered anywhere in Australia is around $700, which is very cheap for a Nismo V2 Urethane bar! $100 cheaper if you are from Adelaide and can pick up from me. Go have a look at what people on SAU have sold Stillen/Chargespeed and other front bars for, and you will see that $700 is an absolute bargain.

  • 3 months later...
Nightcrawler Grand Master

Nightcrawler

Posted
  • Author
Posted

Yeah man, but things are a tad different now - I was looking at bringing in 5 bars in one box, and as such could get the price down to around $700 each at the time. BUT postage prices have gone up significantly in the USA in recent months, and I also realised that I will most certainly get pinged by customs bringing in 5 bars (well over the $1k threshhold), so would get stung a heap in customs fees/duties and GST. So I have done the numbers on 3 bars and can get 3 landed here for around $900 each, then about $100 shipping to any capital city.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • MBS206
      NC MX5

      By MBS206 · Posted

      Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Sorry I meant that we are building the EH for a client.
    • The Bogan
      Torana Lx Gtr Hatch, Lots Of Pictures

      By The Bogan · Posted

      LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...