Jump to content
SAU Community

Recommended Posts

Hi,

These headers were installed on my 370z and I loved the gain and all. I have parted out my car and sold the car that's why I am selling them.

They were installed on my car and travelled for approximately 3000km. So it's in extremely good condition and even comes with the original box

I bought them brandnew from perfectrun and the cost was around $1800 landed and time to order & produce.

Genuine, designed for RHD so it makes life easier as I know USDM headers have a steering rubbing problem and requires more modding work.

Asking price is $1100 which is a bargain for what it is.

Item located in Melbourne south east suburbs and I am willing to post interstates at buyer's expense

Here are some pictures:

Fujitsubo-Super-Exhaust-Manifold-Nissan-370z-09.jpg

-----------------------------------------------------------------------------------

Here's a set of rare GTR R35 Stock Wheels with Nissan Center caps.

20" Super light weight, forged, nice concave, made by Ray's

3 out of 4 are in perfect condition

one with a rash and a scratch. On the same wheel so wouldnt cost more than 2 - 300 bucks if u want a perfect set.

$2999. Can courier to National wide with low freight cost.

577070_3919237027009_1877223085_n.jpg

318028_3919237387018_1499240174_n.jpg

248040_3919237707026_1462028710_3249607_364074218_n.jpg

178928_3919238147037_1462028710_3249608_358366682_n.jpg

600567_3919238627049_1174262140_n.jpg

601056_3919238867055_1324875234_n.jpg

481330_3919239147062_963820610_n.jpg

------------------------------------------------------------------

Genuine Rays Lock nuts in black color (USED)

General worn

goes for about $200 outside, yours for $50

581337_3919264747702_1462028710_3249621_596755100_n.jpg

---------------------------------------------------

Since I don't come onto the forum very often so it is best to contact me via sms: 0422358259

Cheers

I know they are 9.5 front and 10.5 rear but what are the offsets?

Do you have to fit run flat 20's on these or will standard 20 inch tyres go on fine?

Sorry forgot to mention,

20 x 9.5 +45 front and 20 x 10.5 +25 rear. Pretty close to the 370z and 370GT setup apart from being 1 inch wider on each (which is good so you have a flush guard)

As for tyres, normal road tyres are fine

bump, not sure how to edit post

got a Pivot throttle controller for sale too. same model as the one pictured

$130 shipped with harness to fit 370z (not sure about other cars but i think most nissan cars uses the same harness) .

P_311_Throller%20Controller_1_5580022.jpg

Edited by jona1986

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • How would you even adjust the clutch if the pedal already has the correct free play? The operating cylinder has no adjustment in mounting position or rod length. On pull style clutches there is also no ability to adjust the bearing carrier. Push type I can see how adjusting the carrier height makes it all work.   If this is the twin plate clutch did you verify that your friction disks were oriented correctly? It's not mentioned in the directions at all you just have to notice that one side the friction disks have a part number on the hub fingers and a subtle coning to those fingers. Another thing that I noticed was if you put the friction disks in backwards the pressure plate fingers will not be even and flat when the clutch is installed.
    • yeah, mechanically, it is probably do-able, off the top of my head, there would be the transfer case, which I believe will bolt up to the rear of the RWD transmission, the shorter rear tail shaft. A front drive shaft, front diff, engine upper sump, front drive shafts, front hubs and front AWD struts (they are shaped around the front drive shafts), LCAs (at the very least from the front suspension) oil cooler.  You might want the rear diff from an AWD too, so you can be certain the front and rear diff rations are identical.  Who knows what brackets and mounts you might need.  So a whole doner car might be the best option if you need to maintain RHD. Then actually making it work, that would be a whole different story.
    • Take the fall as a warning sign for future endeavours  Stay safe mate
    • hi mate, HKS cooler piping still available by any chance?
×
×
  • Create New...