Jump to content
SAU Community

Recommended Posts

how much for the front seats?

Front seats provisionally gone pending payment, sorry. Pricing for the other items is as follows:

Rear seats: $300

Door cards: $350 (pair)

Carpet: $100

Roof lining: $100

All other plastic trim (includes everything, all pillars, parcel shelf, etc): $300

  • 2 weeks later...
  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Make an offer on items...

The front seats might be back up if I dont hear from the fella who said he would take them.

  • 3 weeks later...

Can you pm me some pics. Might up my offer depending on the condition. Any cuts bumps or imperfections. Please describe. Thanks

Get pics to you tonight.

Michael, Tried to PM you but your box is full.

"Hi Mate,

Did the sale for the front seats go through? Also by any chance do you still have the gear knob? if so how much?

Regards

Scotty"

Michael, Tried to PM you but your box is full.

"Hi Mate,

Did the sale for the front seats go through? Also by any chance do you still have the gear knob? if so how much?

Regards

Scotty"

My PM is screwed, best text or call me.

The seats are provisionally sold, I need to check if payment went through to confirm. I have the gearknob, not sure what it is worth. I can get back to you.

Front seats are officially sold!!!!!! Thanks Theo.

Still have the following, price drop on the door cards and rear seats.

Rear seats: $250

Door cards: $300 (pair)

Carpet: $100

Roof lining: $100

All other plastic trim (includes everything, all pillars, parcel shelf, etc): $300

  • 2 weeks later...
  • 4 weeks later...

All the following still available, make a close offer and you might get it!!!!!

Rear seats: $250

Door cards: $300 (pair)

Carpet: $100

Roof lining: $100

All other plastic trim (includes everything, all pillars, parcel shelf, etc): $300

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...