Jump to content
SAU Community

Recommended Posts

Hi All,

In the last couple of weeks and mainly since our cold Melbourne mornings I'm getting the hand brake dash light staying on in my R33.

Sometimes the light will turn off immediately after the hand brake is released then will turn on again after several seconds, but mostly it will remain on until the engine has been running for 10-15 minutes. For the rest of the day it will continue indicating correctly.

Now i'm wondering if this light might be used to indicate any other car related issues? I do have a power fc but as far as im aware it only uses the engine light for sensor maxing and the rest of the warning lights should act as they did with the OEM ECU.

The car doesn't appear to be driving any different than normal, and it may very well be just a faulting switch on the hand brake. But this starts to seem unlikely when as mentioned early sometimes it does go off as it should then turns on again (without touching the hand brake)

Any help would be very appreciated.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/402319-hand-brake-light-staying-on/
Share on other sites

it also indicates low brake fluid, which can also be an indication that your brake pads are low. check the brake fluid level. if it's low then also check your brake pads, because the lower the pads get, the more fluid is in the calipers and less in the reseviour. if the pads are low then only put a small amount of brake fluid in to get the light to go away, otherwise when you put new pads in you may end up with brake fluid overflowing when you force the pistons back into the caliper

it also indicates low brake fluid, which can also be an indication that your brake pads are low. check the brake fluid level. if it's low then also check your brake pads, because the lower the pads get, the more fluid is in the calipers and less in the reseviour. if the pads are low then only put a small amount of brake fluid in to get the light to go away, otherwise when you put new pads in you may end up with brake fluid overflowing when you force the pistons back into the caliper

Yeah check this

I got caught out searching for a dodgy wire, ripped my seat out and started pulling the floor carpet up and checking the wiring. Then checked the fluid and it was low. Topped it up and light went away. I found my light went out under braking sometimes

Thanks guys, I did wonder when I was in the car the other day if it might also relate to the main braking system.

I tried pumping the brake to see if more pressure made any difference to the warning, but no dice.

The reservoir is below max but still within the indicated min mark. Will give a little bit of a top up and check out how the brake pads are fairing tomorrow. Certainly still have a firm pedal feel so hopefully its just being over sensitive to the reservoir level.

Thanks again and hopefully I'll have good news to report soon.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The attached document is fine. I just downloaded & opened it.
    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
×
×
  • Create New...