Jump to content
SAU Community

Recommended Posts

Thanks man, appreciate it!!!!

Benji real cars fit Pads and Rotors..... Wtf is a hardware kit? Are you fitting a bench vice to your control arm?

The shims and clips things are the hardware kit...

Heres a hardware kit for S13.

FRSport_240SXBrakeKit_512422538844a0b4a3c5cddb.jpg

Once funds permit, I'm going to be ordering a vented carbon fibre bonnet from japan

tumblr_m92mcy3ULe1rohi97o1_1280.jpg

Not really in a hurry for rims as Ive got a pretty much fresh set of KU36's on that set of rims atm.

And coilovers etc are going in in January. From where its at, only needs to be lowered 10mm in the rear and then the control arms will be parallel all round. So I dont negatively affect handling, I'd need to spend more money on things like roll center adjustors if I decided to go any lower than that.

yep - welcome to the joys of gtr ownership.

nice price on the 9's - thats basically what i paid for my -5's (which are usually a few hundred cheaper)

Edited by wedge_r34gtr

Come over to WA and keep me company :-)

What is the work situation like over there?

Could realllly consider it in the new year.

As for car stuff I saw Paul today and got the motor back on track. Also picked up a nice shiny catch can/washer bottle

Mjh, I washed my car today and just polished it afterwards....

do you have any tips on detailing?

Best thing you can get for detailing is a Concours 900 RO kit.

Car looks good as is just get a good sealer and wax to help protect the finish. Check the detailing thread and also check out the Waxit site for quality waxes etc

What is the work situation like over there?

Could realllly consider it in the new year.

As for car stuff I saw Paul today and got the motor back on track. Also picked up a nice shiny catch can/washer bottle

Work's pretty plentifuly, lowest unemployment rate in the country.

i know that catch can, its really shinny :-)

Did you get a water pump? Paul kept hold of my spare N1....

Edited by wedge_r34gtr

Work's pretty plentifuly, lowest unemployment rate in the country.

i know that catch can, its really shinny :-)

Did you get a water pump? Paul kept hold of my spare N1....

Yeah just went with a VL pump.

N1 pumps are more for higher revving motors aren't they? EG drags tracks etc

I'm giving some serious thought to a different job.

The one I have now is good but not enough work or pay

Some guys manage to do 12 hour days regardless of how busy or quite it is an I seem to get the easy short run most days

http://www.gumtree.com.au/s-ad/hoxton-park/cars/nissan-skyline-gtr-must-see-goin-cheap-1995-model/1009072657

14k maybe less could be mine this weekend.

thoughts, fears, loan??? haha

I could very well be wrong but don't GTR's have a BNR prefix for the chassis number?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...