Jump to content
SAU Community

Recommended Posts

Just wanted to ask before I brake something...

I need to pull my bosh 044 I tank out to visualy check it, I assume I just unscrew the plate ontop and it pulls out?

Is ther anything more to this, anything I cannot do or cannot let happen?

Also I also assume their is a rubber seal here somewhere, do I just get a replacement and replace?

Sorry if it's a noob question but I'm already having pump problems I don't want to compound them by Doug so

Ethin stupid I assumed was easy.

Link to comment
https://www.sau.com.au/forums/topic/402522-removing-internal-fuel-pump/
Share on other sites

Make sure theres no dirt and crap that can easily fall in then you undo all the bolts and you should be able to gentle lift it out, it will catch on the float when it's almost all the way out so be careful and just swindle it out gently.

The seal will expand bigger than the groove when it comes out making it a prick to sit back in to seal it, a trick is to put the seal in the freezer to shrink it enough to sit back in the seal groove.

Do a search, there has to be someone that has documented the process on the interwebs somewhere.

Edited by Dobz

When I took my fuel pump out, I just replaced the seal. I tried putting the old one back on but it was a bit annoying and the new fuel pump came with a new seal anyway.

If you worried about the wiring falling into the tank dont, It wont fall in. Like was mention above just make sure none of the fuel line clamps or fuel cell cover bolts fall in.

Also my advice is to wait untill you have less than 1/4 of a tank of petrol or less!

Edited by Mitcho_7

My tank has shit in it, it blocks the mesh cover of my pump,

It's booked in next Friday to have the tank removed cleaned and new pump installed properly.

Last pump I removed the mesh filter was caked.

It's now rapidly getting to the undrivable point and I want to see if I can unclog the mesh to last 1 week. If I half cock up te seal that will be ok till next week yeah? Cos I will..... I can be a bit mechanically special sometimes :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...