Jump to content
SAU Community

Recommended Posts

Hi guys,

just wondering if anyone has sanded, prepared and painted their own rims and if so was it difficult and worth it?

i have wheels now that need to be re painted and have been quoted around a $1000 for most places, i love the look of them and dont want to buy new ones as these really suit the car.

any input is appreciated :)

Hi guys,

just wondering if anyone has sanded, prepared and painted their own rims and if so was it difficult and worth it?

i have wheels now that need to be re painted and have been quoted around a $1000 for most places, i love the look of them and dont want to buy new ones as these really suit the car.

any input is appreciated :)

Yes done a few sets

depends on , tools you have like compressor , sandblaster, spray gun, respirator and clean place to do it

if tyres are off ? Valves out much easier

damage to rims like rash

What you want to paint them in ? colour wise

did my 34 rims with a rattle can the night before a show from pearl white to qm1 lol not the best but didnt take off tyres either , going to soda blast and respray when it warms up more tyres and valves out !!

Worth it yes , be easier if i had free tyre removal and remount and a daily driver to use while off

Edited by Carbon 34

ive restored a set of completely gutter f**ked alloys. they look mint.... but was too much work for the money saved. $1000 will buy you a good set of alloys on any forum and save the skin on your knuckles

There's a mightycarmods video on YouTube which shows you how to do it.

I've personally done this about 6-7 times. Spray painting them can work really well (especially considering you won't be spending much) if you take the effort to properly prepare your wheels prior to spraying.

Get yourself sandpaper and work your way up the grits and finish with a 1500 grit sand (don't go too smooth otherwise paint won't stick properly). Obviously if your wheels have gutter rash etc., you may need to do some filling. After the prep work is done remove all the crap with a good wax and grease remover and mask up the valves. I use cards and wedge them between the wheel and tyre so as to not get any overspray on the tyres (much easier than masking) and then you wanna spray a few coats of primer, when dry a few coats of your actual color spray and finish off with multiple coats of clear (at least 4). After the paint is completely dry wet sand lightly using 2000 grit sandpaper.

The type of paint you use is also very important - I generally find that any high temp enamel spray works well (engine enamel, caliper paint or actual wheel paint).

Tip: don't spray too close, or on one spot for too long as you'll get runs which are ok if it's on your primer (as you can sand away) but will stuff up the look of your wheels if on your color or clear spray.

Dont paint your rims yourself , i just get my sets sandblasted and powdercoated , the finish is amazing and hard wearing .

Ring Oleg at HWH Powder Coaters Edwardstown , Oleg sandblasted and powdercoated my work VS-XX for $90 each -

Heres my thread

http://www.skylinesa...iece-work-rims/

Edited by NISSAN GTR

best bet is powdercoating in above post ^^

but if you want to do a DIY and cant afford to have wheels separated rebalanced and etc (unless your tyres are now racing slicks :P)

have had wheels painted at our crash shop before, not all that difficult just takes a long time, as mentioned in above posts, start off with a coarse fine grit (approx 500) and work up from there to say 800, i would suggest using it wet not dry and even use some scotchbrite for thoes areas u cant reach for good measure.

you can use an etch primer for the area of which u have repaired (gutter rash) sand them back using same method untill your happy with them.

then apply a "drop coat" which is a light coating of the colour you want, alternatively, if your going for a colour which doesnt cover very well put down a basecoat of black but only mist it on (that goes for the dropcoat and basecoat)

then apply how many ever layers of paint desired to reach aquired colour/depth always allow for drying time and finish with a few coats of clear.

important tip is to take time in masking the wheels up properly and make sure all the air is out of the tyres so its easier to compress the sidewall to get tape in there, also a few newspapers come in handy if you dont have the proper stuff to cover them. 1 and 2 inch masking tape will work for this application also.

hope this helps as ive tried to cover what i can remmeber from the painters telling me!

best bet is powdercoating in above post ^^

but if you want to do a DIY and cant afford to have wheels separated rebalanced and etc (unless your tyres are now racing slicks :P)

have had wheels painted at our crash shop before, not all that difficult just takes a long time, as mentioned in above posts, start off with a coarse fine grit (approx 500) and work up from there to say 800, i would suggest using it wet not dry and even use some scotchbrite for thoes areas u cant reach for good measure.

you can use an etch primer for the area of which u have repaired (gutter rash) sand them back using same method untill your happy with them.

then apply a "drop coat" which is a light coating of the colour you want, alternatively, if your going for a colour which doesnt cover very well put down a basecoat of black but only mist it on (that goes for the dropcoat and basecoat)

then apply how many ever layers of paint desired to reach aquired colour/depth always allow for drying time and finish with a few coats of clear.

important tip is to take time in masking the wheels up properly and make sure all the air is out of the tyres so its easier to compress the sidewall to get tape in there, also a few newspapers come in handy if you dont have the proper stuff to cover them. 1 and 2 inch masking tape will work for this application also.

hope this helps as ive tried to cover what i can remmeber from the painters telling me!

where is your shop mate?im looking at getting a 2pac setup for my self as im ok with painting acrylics, but if i can get my ford BA bodykit done in shop at a good price i will.

You could plasti-dip them yourself, no sanding needed, its lasted ok so far on mine, but if theres a scratch you just spray over the top and its like new again :D

$30 a can, 2 cans will do all your rims

plus you can always divert to the old colour when you please :woot:

where is your shop mate?im looking at getting a 2pac setup for my self as im ok with painting acrylics, but if i can get my ford BA bodykit done in shop at a good price i will.

Pm'd :D

I dont the colour jet and have some old impuls too.

Your on Australian ford forums as i recognise that car, im 'Sprint' on there.

All fitted and sorted now , the 245 went on the 10.5 so easy , like butter!

Edited by cosworth1971

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...